D-Link 3324SRi Reference Manual - Page 140

config link_aggregation algorithm, Specifies the group ID. The Switch allows

Get D-Link 3324SRi - Switch - Stackable PDF manuals and user guides
UPC - 790069256042
View all D-Link 3324SRi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 140 highlights

xStack Gigabit Layer 3 Switch Command Line Interface Manual Parameters Restrictions group _id − Specifies the group ID. The Switch allows up to 32 link aggregation groups to be configured. The group number identifies each of the groups. master_port − Master port ID. Specifies which port (by port number) of the link aggregation group will be the master port. All of the ports in a link aggregation group will share the port configuration with the master port. The port is specified by listing the switch number and the port number on that switch, separated by a colon. For example, 1:3 specifies switch number 1, port 3. 2:4 specifies switch number 2, port 4. ports − Specifies a range of ports that will belong to the link aggregation group. The port list is specified by listing the lowest switch number and the beginning port number on that switch, separated by a colon. Then the highest switch number, and the highest port number of the range (also separated by a colon) are specified. The beginning and end of the port list range are separated by a dash. For example, 1:3 specifies switch number 1, port 3. 2:4 specifies switch number 2, port 4. 1:3-2:4 specifies all of the ports between switch 1, port 3 and switch 2, port 4 − in numerical order. Ports may be listed in only one port aggregation group, that is, link aggregation groups may not overlap. state [enable | disable] − Allows you to enable or disable the specified link aggregation group. Only administrator-level users can issue this command. Link aggregation groups may not overlap. Example usage: To define a load-sharing group of ports, group-id 1,master port 5 of module 1 with group members ports 5-7 plus port 9: DGS-3324SRi:4#config link_aggregation group_id 1 master_port 1:5 ports 1:5-1:7, 1:9 Command: config link_aggregation group_id 1 master_port 1:5 ports 1:5-1:7, 1:9 Success. DGS-3324SRi:4# config link_aggregation algorithm Purpose Syntax Description Parameters Used to configure the link aggregation algorithm. config link_aggregation algorithm [mac_source | mac_destination | mac_source_dest | ip_source | ip_destination | ip_source_dest] This command configures to part of the packet examined by the Switch when selecting the egress port for transmitting load-sharing data. This feature is only available using the address-based loadsharing algorithm. mac_source − Indicates that the Switch should examine the MAC source address. 132

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340
  • 341
  • 342
  • 343
  • 344
  • 345
  • 346
  • 347
  • 348
  • 349
  • 350
  • 351
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
xStack Gigabit Layer 3 Switch Command Line Interface Manual
Parameters
group _id <value 1-32>
−
Specifies the group ID. The Switch allows
up to 32 link aggregation groups to be configured. The group
number identifies each of the groups.
master_port <port>
−
Master port ID. Specifies which port (by port
number) of the link aggregation group will be the master port.
All of
the ports in a link aggregation group will share the port configuration
with the master port. The port is specified by listing the switch
number and the port number on that switch, separated by a colon.
For example, 1:3 specifies switch number 1, port 3. 2:4 specifies
switch number 2, port 4.
ports <portlist>
−
Specifies a range of ports that will belong to the
link aggregation group. The port list is specified by listing the lowest
switch number and the beginning port number on that switch,
separated by a colon. Then the highest switch number, and the
highest port number of the range (also separated by a colon) are
specified. The beginning and end of the port list range are separated
by a dash. For example, 1:3 specifies switch number 1, port 3. 2:4
specifies switch number 2, port 4. 1:3-2:4 specifies all of the ports
between switch 1, port 3 and switch 2, port 4
−
in numerical order.
Ports may be listed in only one port aggregation group, that is, link
aggregation groups may not overlap.
state [enable | disable]
−
Allows you to enable or disable the
specified link aggregation group.
Restrictions
Only administrator-level users can issue this command. Link
aggregation groups may not overlap.
Example usage:
To define a load-sharing group of ports, group-id 1,master port 5 of module 1 with group members ports 5-7 plus port
9:
DGS-3324SRi:4#config link_aggregation group_id 1 master_port
1:5 ports 1:5-1:7, 1:9
Command: config link_aggregation group_id 1 master_port 1:5
ports 1:5-1:7, 1:9
Success.
DGS-3324SRi:4#
config link_aggregation algorithm
Purpose
Used to configure the link aggregation algorithm.
Syntax
config link_aggregation algorithm [mac_source |
mac_destination | mac_source_dest | ip_source |
ip_destination | ip_source_dest]
Description
This command configures to part of the packet examined by the
Switch when selecting the egress port for transmitting load-sharing
data. This feature is only available using the address-based load-
sharing algorithm.
Parameters
mac_source
−
Indicates that the Switch should examine the MAC
source address.
132