D-Link 3324SRi Reference Manual - Page 128

xStack Gigabit Layer 3 Switch Command Line Interface Manual

15

VLAN C

OMMANDS

The xStack family of switches incorporate the idea of protocol-based VLANs. This standard, defined by the IEEE 802.1v

standard maps packets to protocol-defined VLANs by examining the type octet within the packet header to discover the type of

protocol associated with it. After assessing the protocol, the Switch will forward the packets to all ports within the protocol-

assigned VLAN. This feature will benefit the administrator by better balancing load sharing and enhancing traffic classification.

The switch supports fifteen (15) pre-defined protocols for configuring protocol-based VLANs. The user may also choose a

protocol that is not one of the fifteen defined protocols by properly configuring the

userDefined

protocol VLAN. The supported

protocols for the protocol VLAN function on this Switch include IP, IPX, DEC, DEC LAT, SNAP, NetBIOS, AppleTalk, XNS,

SNA, IPv6, RARP and VINES.

The VLAN commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following

table.

Command

Parameters

create vlan

<vlan_name 32> {tag <vlanid 2-4094> | {type {1q_vlan

{advertisement} | [protocol-ip | protocol-ipx802dot3 | protocol-

ipx802dot2 | protocol-ipxSnap | protocol-ipxEthernet2 | protocol-

appleTalk | protocol-decLat | protocol-decOther | protocol-

sna802dot2 | protocol-snaEthernet2 | protocol-netBios | protocol-

xns | protocol-vines | protocol-ipV6 | protocol-userDefined

<hex0x0-0xffff> encap [ethernet | llc | snap | all] | protocol-rarp]}}

delete vlan

<vlan_name 32>

config vlan

<vlan_name 32> {[add [tagged | untagged | forbidden] <portlist> |

advertisement [enable | disable]}

config vlan

<vlan_name 32> delete <portlist>

config gvrp

[<portlist> | all] {state [enable | disable] | ingress_checking [enable

| disable] | acceptable_frame [tagged_only | admit_all] | pvid

<vlanid 1-4094>}

enable gvrp

disable gvrp

show vlan

{<vlan_name 32>}

show gvrp

{<portlist>}

Each command is listed, in detail, in the following sections.

create vlan

Purpose

Used to create a VLAN on the Switch.

Syntax

create vlan <vlan_name 32> {tag <vlanid 2-4094> | {type

{1q_vlan {advertisement} | [protocol-ip | protocol-ipx802dot3 |

protocol-ipx802dot2 | protocol-ipxSnap | protocol-

ipxEthernet2 | protocol-appleTalk | protocol-decLat | protocol-

decOther | protocol-sna802dot2 | protocol-snaEthernet2 |

protocol-netBios | protocol-xns | protocol-vines | protocol-

ipV6 | protocol-userDefined <hex0x0-0xffff> encap [ethernet |

llc | snap | all] | protocol-rarp]}}

Description

This command allows you to create a VLAN on the Switch. The

h

bt

802 1Q VLAN

t

lb

d

120

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 128

VLAN Commands, create vlan

Page 128 highlights