D-Link 3324SRi Reference Manual - Page 231

xStack Gigabit Layer 3 Switch Command Line Interface Manual

config access_profile profile_id (for Ethernet)

the Switch.

replace_dscp <value 0-63>

−

Allows you to specify a value to be

written to the DSCP field of an incoming packet that meets the

criteria specified in the first part of the command. This value will

over-write the value in the DSCP field of the packet.

deny

– Specifies that packets that do not match the access profile

are not permitted to be forwarded by the Switch and will be filtered.

delete access_id <value 1-100>

−

Use this command to delete a

specific rule from the Ethernet profile. Up to 100 rules may be

specified for the Ethernet access profile.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To configure a rule for the Ethernet access profile:

DGS-3324SRi:4#

DGS-3324SRi:4#config access profile profile_id 1 add access_id 1

ethernet vlan Trinity 802.1p 1 port 1:1 permit priority 1 replace priority

Command: config access profile profile_id 1 add access_id 1 ethernet

vlan Trinity 802.1p 1 port 1:1 permit priority 1 replace priority

Success.

create access_profile (IP)

Purpose

Used to create an access profile on the Switch by examining the IP

part of the packet header. Masks entered can be combined with the

values the Switch finds in the specified frame header fields. Specific

values for the rules are entered using the

config access_profile

command, below.

Syntax

create access_profile ip {vlan | source_ip_mask <netmask> |

destination_ip_mask <netmask> | dscp | [icmp {type | code} |

igmp {type} | tcp {src_port_mask <hex 0x0-0xffff> |

dst_port_mask <hex 0x0-0xffff> | flag_mask [all | {urg | ack | psh

| rst | syn | fin}]} | udp {src_port_mask <hex 0x0-0xffff> |

dst_port_mask <hex 0x0-xffff>} | protocol_id {user _mask <hex

0x0-0xffffffff>}]} profile_id <value 1-8>}

Description

This command will allow the user to create a profile for packets that

may be accepted or denied by the Switch by examining the IP part of

the packet header. Specific values for rules pertaining to the IP part

of the packet header may be defined by configuring the

config

access_profile

command for IP, as stated below.

Parameters

ip

- Specifies that the Switch will look into the IP fields in each packet

with special emphasis on one or more of the following:

•

vlan

−

Specifies a VLAN mask.

•

source_ip_mask <netmask>

−

Specifies an IP address mask

for the source IP address.

223

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 231

config access_profile profile_id for Ethernet, create access_profile IP

Page 231 highlights