D-Link 3324SRi Reference Manual - Page 228

xStack Gigabit Layer 3 Switch Command Line Interface Manual

Command

Parameters

create access_profile

ip {vlan | source_ip_mask <netmask> | destination_ip_mask

<netmask> | dscp | [icmp {type | code} | igmp {type} | tcp

{src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>

| flag_mask [all | {urg | ack | psh | rst | syn | fin}]} | udp

{src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-xffff>}

| protocol_id {user _mask <hex 0x0-0xffffffff> }]} profile_id <value

1-8>}

config access_profile

profile_id

<value 1-8> [add access_id <value 1-100> ip {vlan <vlan_name

32> | source_ip <ipaddr> | destination_ip <ipaddr> | dscp <value

0-63> | [icmp {type <value 0-255> code <value 0-255>} | igmp

{type <value 0-255>} | tcp {src_port <value 0-65535> | dst_port

<value 0-65535> | urg | ack | psh | rst | syn | fin} | udp {src_port

<value 0-65535> | dst_port <value 0-65535>} | protocol_id <value

0 - 255>

{user_define <hex 0x0-0xffffffff> }]} port <port> [permit

{priority <value 0-7> {replace_priority} | replace_dscp <value 0-

63>} | deny] delete <value 1-100>]


packet_content_mask {offset_0-15 <hex 0x0-0xffffffff> <hex 0x0-

0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_16-31

<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex

0x0-0xffffffff> | offset_32-47 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>

<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | offset_48-63 <hex 0x0-

0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-

0xffffffff> | offset_64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>

<hex 0x0-0xffffffff> <hex 0x0-0xffffffff>} profile_id <value 1-8>}


profile_id

<value 1-8> [add access_id <value 1-100> packet_content

{offset_0-15 <hex0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-

0xffffffff> <hex 0x0-0xffffffff> | offset_16-31 <hex 0x0-0xffffffff>

<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> |

offset_32-47 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff><hex 0x0-

0xffffffff> <hex 0x0-0xffffffff> | offset_48-63 <hex 0x0-0xffffffff>

<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> |

offset_64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-

0xffffffff> <hex0x0-0xffffffff>} port <port> [permit {priority <value 0-

7> {replace_priority} | replace_dscp <value 0-63>} | deny] delete

<value 1-100>]


ipv6 {class | flowlabel | source_ipv6_mask <ipv6mask> |

destination_ipv6_mask <ipv6mask>}] profile_id <value 1-8>}

<value 1-8> add access_id <value 1-100> ipv6 {class <value 0-

255> | flowlabel <hex 0x0-0xfffff> | source_ipv6 <ipv6addr> |

destionation_ipv6 <ipv6addr>} port <port> [permit {priority <value

0-7> {replace_priority}} | deny] | delete <value 1-100>]


profile_id

Each command is listed, in detail, in the following sections.

create access_profile (for Ethernet)

Purpose

Used to create an access profile on the Switch by examining the

Ethernet part of the packet header. Masks entered can be combined

with the values the Switch finds in the specified frame header fields.

Specific values for the rules are entered using the

config

access_profile

command, below.

Syntax

create access_profile [ethernet {vlan | source_mac <macmask

000000000000-ffffffffffff> | destination_mac <macmask

000000000000-ffffffffffff> | 802.1p | ethernet_type} profile_id

220

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 228

create access_profile for Ethernet, create access_profile [ethernet {vlan | source_mac <macmask

Page 228 highlights