D-Link 3324SRi Reference Manual - Page 138

xStack Gigabit Layer 3 Switch Command Line Interface Manual

16

L

INK

A

GGREGATION

C

OMMANDS

The link aggregation commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the

following table.

Command

Parameters

create link_aggregation

group_id <value 1-32> {type [lacp | static]}

delete link_aggregation

group_id <value 1-32>

config link_aggregation

group_id <value1-32> {master_port <port> | ports <portlist>

state [enable | disable]}

config link_aggregation

algorithm

[mac_source | mac_destination | mac_source_dest | ip_source

| ip_destination | ip_source_dest]

show link_aggregation

{group_id <value 1-32> | algorithm}

config lacp_port

<portlist> mode [active | passive]

show lacp_port

{<portlist>}

Each command is listed, in detail, in the following sections.

create link_aggregation

Purpose

Used to create a link aggregation group on the Switch.

Syntax

create link_aggregation group_id <value 1-32> {type [lacp |

static]}

Description

This command will create a link aggregation group with a unique

identifier.

Parameters

<value 1-32>

−

Specifies the group ID. The Switch allows up to 32

link aggregation groups to be configured. The group number

identifies each of the groups.

type

– Specify the type of link aggregation used for the group. If

the type is not specified the default type is static.

±

±

lacp

– This designates the port group as LACP compliant.

LACP allows dynamic adjustment to the aggregated port

group. LACP compliant ports may be further configured (see

config lacp_ports). LACP compliant must be connected to

LACP compliant devices.

static

– This designates the aggregated port group as

static. Static port groups can not be changed as easily as

LACP compliant port groups since both linked devices must

be manually configured if the configuration of the trunked

group is changed. If static link aggregation is used, be sure

that both ends of the connection are properly configured and

that all ports have the same speed/duplex settings.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To create a link aggregation group:

130

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 138

Link Aggregation Commands, create link_aggregation

Page 138 highlights