D-Link 3324SRi Reference Manual - Page 244

xStack Gigabit Layer 3 Switch Command Line Interface Manual

26

T

RAFFIC

S

EGMENTATION

C

OMMANDS

Traffic segmentation allows you to further sub-divide VLANs into smaller groups of ports that will help to reduce traffic on the

VLAN. The VLAN rules take precedence, and then the traffic segmentation rules are applied. The traffic segmentation

commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table.

Command

Parameters

config traffic_segmentation

[<portlist> | all] forward_list [null | all | <portlist>]

show traffic_segmentation

{<portlist>}

Each command is listed, in detail, in the following sections.


Purpose

Used to configure traffic segmentation on the Switch.

Syntax

config traffic_segmentation [<portlist> | all] forward_list [null

| all | <portlist>]

Description

The


command is used to configure

traffic segmentation on the Switch.

Parameters

<portlist>

−

Specifies a range of ports that will be configured for

traffic segmentation. The port list is specified by listing the lowest

switch number and the beginning port number on that switch,

separated by a colon. Then the highest switch number, and the

highest port number of the range (also separated by a colon) are

specified. The beginning and end of the port list range are

separated by a dash. For example, 1:3 specifies switch number

1, port 3. 2:4 specifies switch number 2, port 4. 1:3-2:4 specifies

all of the ports between switch 1, port 3 and switch 2, port 4

−

in

numerical order.

all

– Specifies all ports on the Switch.

forward_list

−

Specifies a port or range of ports that will receive

forwarded frames from the ports specified in the portlist, above.

Restrictions

Only administrator-level users can issue this command.

•

null

−

No ports are specified

•

all

– Specifies all ports on the Switch.

•

<portlist>

−

Specifies a range of ports for the forwarding list.

This list must be on the same switch previously specified

for traffic segmentation (i.e. following the

<portlist>

specified above for


).

Example usage:

To configure ports 1 through 10 to be able to forward frames to port 11 through 15:

236

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 244

Traffic Segmentation Commands, config traffic_segmentation

Page 244 highlights