D-Link 3324SRi Reference Manual - Page 303

xStack Gigabit Layer 3 Switch Command Line Interface Manual

37

DVMRP C

OMMANDS

The DVMRP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the

following table.

Command

Parameters

config dvmrp

[ipif <ipif_name 12> | all] {metric <value 1-31> | probe <sec 1-

65535> | neighbor_timeout <sec 1-65535> | state [enable |

disable]}

enable dvmrp

disable dvmrp

show dvmrp neighbor

{ipif <ipif_name 12> | ipaddress <network_address>}

show dvmrp nexthop

{ipaddress <network_address> | ipif <ipif_name 12>}

show dvmrp

routing_table

{ipaddress <network_address>}

show dvmrp

{ipif <ipif_name 12>}

Each command is listed, in detail, in the following sections.

config dvmrp

Purpose

Used to configure DVMRP on the Switch.

Syntax

config dvmrp [ipif <ipif_name 12> | all] {metric <value 1-31>

| probe <sec 1-65535> | neighbor_timeout <sec 1-65535> |

state [enable | disable]}

Description

This command is used to configure DVMRP on the Switch.

Parameters

ipif <ipif_name 12>

−

The name of the IP interface for which

DVMRP is to be configured.

all

−

Specifies that DVMRP is to be configured for all IP

interfaces on the Switch.

metric <value 1-31>

−

Allows the assignment of a DVMRP route

cost to the above IP interface. A DVMRP route cost is a relative

number that represents the real cost of using this route in the

construction of a multicast delivery tree. It is similar to, but not

defined as, the hop count in RIP. The default is 1.

probe <second 1-65535>

−

DVMRP defined an extension to

IGMP that allows routers to query other routers to determine if a

DVMRP neighbor is present on a given subnetwork or not. This

is referred to as a ‘probe’. This entry will set an intermittent

probe (in seconds) on the device that will transmit dvmrp

messages, depending on the time specified. This probe is also

used to “keep alive” the connection between DVMRP enabled

devices. The default value is 10 seconds.

neighbor_timeout <second 1-65535>

−

The time period for

which DVMRP will hold Neighbor Router reports before issuing

poison route messages. The default value is 35 seconds.

295

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 303

DVMRP Commands, config dvmrp

Page 303 highlights