D-Link 3324SRi Reference Manual - Page 289

xStack Gigabit Layer 3 Switch Command Line Interface Manual

config route redistribute dst rip src

internal | external | type_1 | type_2 | inter+e1 | inter+e2]]

{metric <value>}

Description

Route redistribution allows routers on the network that are running

different routing protocols to exchange routing information. This is

accomplished by comparing the routes stored in the various

router’s routing tables and assigning appropriate metrics. This

information is then exchanged among the various routers

according to the individual routers current routing protocol. The

Switch can redistribute routing information between the OSPF and

RIP routing protocols to all routers on the network that are running

OSPF or RIP. Routing information entered into the Static Routing

Table on the local switch is also redistributed.

Parameters

src {all | internal | external | type_1 | type_2 | inter+e1 | inter+e2}

−

Allows the selection of the protocol of the source device. The user

may choose between:

metric <value>

−

Allows the entry of an OSPF interface cost. This

is analogous to a Hop Count in the RIP routing protocol.

Restrictions

Only administrator-level users can issue this command.

•

all

– Specifies both internal an external.

•

internal

– Specifies the internal protocol of the source device.

•

inter+e1

– Specifies the internal protocol AND type 1 of the

external protocol.

•

external

- Specifies the external protocol of the source

device.

•

type_1

- Calculates the metric (for RIP to OSPF) by adding

the destination’s interface cost to the metric entered in the

Metric field.

•

type_2

- Uses the metric entered in the Metric field without

change. This field applies only when the destination field is

OSPF.

•

inter+e2

– Specifies the internal protocol AND type 2 of the

external protocol.

Example Usage:

To configure route redistributions:

DGS-3324SRi:4#config route redistribute dst ospf src rip mettype

type_1 metric 2

Command: config route redistribute dst ospf src rip mettype

type_1 metric 2

Success.

DGS-3324SRi:4#

281

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 289

config route redistribute dst rip src, internal | external | type_1 | type_2 | inter+e1 | inter+e2]]

Page 289 highlights