D-Link DES-3828 Product Manual - Page 109

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

105

15

VLAN

C

OMMANDS

Along with normal VLAN configurations, this Switch now incorporate Double VLANs. Better known as Q-IN-Q VLANs, Double

VLANs allow network providers to expand their VLAN configurations to place VLANs within a larger inclusive VLAN, which adds

a new layer to the VLAN configuration. This basically lets large ISP's create L2 Virtual Private Networks and also create transparent

LANs for their customers, which will connect two or more customer LAN points without over complicating configurations on the

client's side. Not only will over-complication be avoided, but now the administrator has over 4000 VLANs in which over 4000

VLANs can be placed, therefore greatly expanding the VLAN network.

Implementation of this feature adds a VLAN frame to an existing VLAN frame for the ISP VLAN recognition and classification. To

ensure devices notice this added VLAN frame, an Ethernet encapsulation, here known as a tpid, is also added to the frame. The device

recognizes this tpid and therefore checks the VLAN tagged packet to see if a provider VLAN tag has been added. If so, the packet is

then routed through this provider VLAN, which contains smaller VLANs with similar configurations to ensure speedy and guaranteed

routing destination of the packet.

The VLAN commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table.

Command

Parameters

create vlan

<vlan_name 32> {tag <vlanid 1-4094> | advertisement}

show vlan

{<vlan_name 32>}

config vlan

<vlan_name 32> {[add [tagged | untagged | forbidden] |

delete] <portlist> | advertisement [enable | disable]}

delete vlan

<vlan_name 32>

create vlan vlanid

<vidlist> {advertisement}

show vlan vlanid

<vidlist>

config vlan vlanid

<vidlist> {add [ tagged | untagged | forbidden ] | delete

<portlist> | advertisement [enable | disable] | name

<name>}

delete vlan vlanid

<vidlist>

config gvrp

[<portlist> | all ] {state [enable | disable] |

ingress_checking [enable | disable] | acceptable_frame

[tagged_only | admit_all] | pvid <vlanid 1-4094>}

enable gvrp

disable gvrp

show gvrp

{<portlist>}

create dot1v_protocol_group

group_id

<id>

config dot1v_protocol_group

group_id

< id> [add | delete] protocol

[ethernet_2|

ieee802.3_snap| ieee802.3_llc]

< protocol_value>

delete dot1v_protocol_group

[group_id <id> | all]

show dot1v_protocol_group

{group_id <id>}

config port dot1v ports

<portlist> | all] [add protocol_group group_id <id>

vlan< vlan_name 32> | delete protocol_group

[group_id <id>|all]

show port dot1v

{ports <portlist>}

enable pvid auto_assign

disable pvid auto_assign

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

D-Link DES-3828 Product Manual - Page 109

VLAN Commands, Along with normal VLAN configurations

Page 109 highlights