Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 186

create route redistribute dst rip src, mettype 1

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 186 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual Allowed Metric Type combinations are mettype 1 or mettype 2. The metric value 0 above will be redistributed in OSPF as the metric 20. Example usage: To add route redistribution settings: DES-3800:admin#create route redistribute dst ospf src rip Command: create route redistribute dst ospf src rip Success. DES-3800:admin# create route redistribute dst rip src Purpose Syntax Description Parameters Restrictions Used to add route redistribution settings for the exchange of OSPF routes to RIP routes on the Switch. create route redistribute dst rip src [local | static | ospf {all | internal | external | type_1 | type_2 | inter+e1 | inter+e2}] {metric } This command will redistribute routing information between the OSPF and RIP routing protocols to all routers on the network that are running OSPF or RIP. Routing information entered into the Static Routing Table on the local xStack switch is also redistributed src − Allows the selection of the protocol of the source device, as being either local, static or OSPF. After selecting the source device, the user may set the following parameters for that source device from the following options: • all - Specifies both internal an external. • internal - Specifies the internal protocol of the source device. • external - Specifies the external protocol of the source device. • type_1 - Calculates the metric (for RIP to OSPF) by adding the destination's interface cost to the metric entered in the Metric field. • type_2 - Uses the metric entered in the Metric field without change. This field applies only when the destination field is OSPF. • inter+e1 - Specifies the internal protocol AND type 1 of the external protocol. • inter+e2 - Specifies the internal protocol AND type 2 of the external protocol. metric − Allows the entry of an OSPF interface cost. This is analogous to a HOP Count in the RIP routing protocol. Only Administrator or Operator-level users can issue this command. 182

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

182

Allowed Metric Type combinations are

mettype 1

mettype 2

. The metric value

above will be redistributed in OSPF as the metric

Example usage:

To add route redistribution settings:

DES-3800:admin#create route redistribute dst ospf

src rip

Command: create route redistribute dst ospf src rip

Success.

DES-3800:admin#

create route redistribute dst rip src

Purpose

Used to add route redistribution settings for the exchange of OSPF routes

to RIP routes on the Switch.

Syntax

create route redistribute dst rip src [local | static | ospf {all | internal |

external | type_1 | type_2 | inter+e1 | inter+e2}] {metric <value 0-16>}

Description

This command will redistribute routing information between the OSPF and

RIP routing protocols to all routers on the network that are running OSPF

or RIP. Routing information entered into the Static Routing Table on the

local xStack switch is also redistributed

Parameters

src

−

Allows the selection of the protocol of the source device, as being

either local, static or OSPF. After selecting the source device, the user may

set the following parameters for that source device from the following

options:

•

all

– Specifies both internal an external.

•

internal

– Specifies the internal protocol of the source device.

•

external

- Specifies the external protocol of the source device.

•

type_1

- Calculates the metric (for RIP to OSPF) by adding the

destination’s interface cost to the metric entered in the Metric

field.

•

type_2

- Uses the metric entered in the Metric field without

change. This field applies only when the destination field is

OSPF.

•

inter+e1

– Specifies the internal protocol AND type 1 of the

external protocol.

•

inter+e2

– Specifies the internal protocol AND type 2 of the

external protocol.

metric <value 0-16>

−

Allows the entry of an OSPF interface cost. This is

analogous to a HOP Count in the RIP routing protocol.

Restrictions

Only Administrator or Operator-level users can issue this command.