D-Link DES-3828 Product Manual - Page 302

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

enable ssl

Purpose

To enable the SSL function on the Switch.

Syntax

enable ssl {ciphersuite {RSA_with_RC4_128_MD5 |

RSA_with_3DES_EDE_CBC_SHA |

DHE_DSS_with_3DES_EDE_CBC_SHA |

RSA_EXPORT_with_RC4_40_MD5}}

Description

This command will enable SSL on the Switch by implementing any

one or combination of listed ciphersuites on the Switch. Entering this

command without a parameter will enable the SSL status on the

Switch. Enabling SSL will disable the web-manager on the Switch.

Parameters

ciphersuite

- A security string that determines the exact

cryptographic parameters, specific encryption algorithms and key

sizes to be used for an authentication session. The user may choose

any combination of the following:

•

RSA_with_RC4_128_MD5

– This ciphersuite combines the

RSA key exchange, stream cipher RC4 encryption with

128-bit keys and the MD5 Hash Algorithm.

•

RSA_with_3DES_EDE_CBC_SHA

- This ciphersuite

combines the RSA key exchange, CBC Block Cipher

3DES_EDE encryption and the SHA Hash Algorithm.

•

DHE_DSS_with_3DES_EDE_CBC_SHA

- This ciphersuite

combines the DSA Diffie Hellman key exchange, CBC

Block Cipher 3DES_EDE encryption and SHA Hash

Algorithm.

•

RSA_EXPORT_with_RC4_40_MD5

- This ciphersuite

combines the RSA Export key exchange, stream cipher

RC4 encryption with 40-bit keys.

The ciphersuites are enabled by default on the Switch, yet the SSL

status is disabled by default. Enabling SSL with a ciphersuite will not

enable the SSL status on the Switch.

Restrictions

Only Administrator or Operator-level users can issue this command.

Example usage:

To enable SSL on the Switch for all ciphersuites:

DES-3800:admin#enable ssl

Command:enable ssl

Note: Web will be disabled if SSL is enabled.

Success.

DES-3800:admin#

NOTE:

Enabling SSL on the Switch will enable all ciphersuites. To utilize a

particular ciphersuite, the user must eliminate other ciphersuites by using

the

disable ssl

command along with the appropriate ciphersuites.

NOTE:

Enabling the SSL function on the Switch will disable the port for

the web manager (port 80). To log on to the web based manager, the

entry of your URL must begin with

https://

. (ex. https://10.90.90.90)

298

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

D-Link DES-3828 Product Manual - Page 302

enable ssl, DHE_DSS_with_3DES_EDE_CBC_SHA

Page 302 highlights