Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 274

show authen server_group, config authen parameter response_timeout, Total Entries : 4

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 274 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual show authen server_group Purpose Syntax Description Parameters Restrictions Used to view authentication server groups on the Switch. show authen server_group This command will display authentication server groups currently configured on the Switch. This command will display the following fields: Group Name: The name of the server group currently configured on the Switch, including built in groups and user defined groups. IP Address: The IP address of the server host. Protocol: The authentication protocol used by the server host. - Enter an alphanumeric string of up to 15 characters to define the previously created server group to be viewed. Entering this command without the parameter will display all authentication server groups on the Switch. None. Example usage: To view authentication server groups currently set on the Switch. DES-3800:admin#show authen server_group Command: show authen server_group Group Name Darren TACACS tacacs TACACS tacacs+ xtacacs IP Address 10.53.13.2 Protocol -------- 10.53.13.94 (This group has no entry) (This group has no entry) Total Entries : 4 DES-3800:admin# config authen parameter response_timeout Purpose Syntax Description Parameters Restrictions Used to configure the amount of time the Switch will wait for a user to enter authentication before timing out. config authen parameter response_timeout This command will set the time the Switch will wait for a response of authentication from the user. response_timeout - Set the time, in seconds, the Switch will wait for a response of authentication from the user attempting to log in from the command line interface or telnet interface. 0 disables the timeout for the response. The default value is 30 seconds. Only Administrator-level users can issue this command. Example usage: To configure the response timeout for 60 seconds: DES-3800:admin# config authen parameter response_timeout 60 Command: config authen parameter response_timeout 60 270

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

270

show authen server_group

Purpose

Used to view authentication server groups on the Switch.

Syntax

show authen server_group <string 15>

Description

This command will display authentication server groups currently

configured on the Switch.

This command will display the following fields:

Group Name: The name of the server group currently configured on

the Switch, including built in groups and user defined groups.

IP Address: The IP address of the server host.

Protocol: The authentication protocol used by the server host.

Parameters

- Enter an alphanumeric string of up to 15 characters to

define the previously created server group to be viewed.

Entering this command without the

parameter will display all

authentication server groups on the Switch.

Restrictions

None.

Example usage:

To view authentication server groups currently set on the Switch.

DES-3800:admin#show authen server_group

Command: show authen server_group

Group Name

IP Address

Protocol

---------------

-----------------

--------

Darren

10.53.13.2

TACACS

tacacs

10.53.13.94

TACACS

tacacs+

(This group has no entry)

xtacacs

(This group has no entry)

Total Entries : 4

DES-3800:admin#

config authen parameter response_timeout

Purpose

Used to configure the amount of time the Switch will wait for a user

to enter authentication before timing out.

Syntax

config authen parameter response_timeout <int 0-255>

Description

This command will set the time the Switch will wait for a response of

authentication from the user.

Parameters

response_timeout <int 0-255>

- Set the time, in seconds, the Switch

will wait for a response of authentication from the user attempting to

. 0

disables

the timeout for the response. The default value is 30 seconds.

Restrictions

Only Administrator-level users can issue this command.

Example usage:

To configure the response timeout for 60 seconds:

DES-3800:admin# config authen parameter

response_timeout 60

Command: config authen parameter response_timeout 60