Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 113

show vlan vlanid, config vlan vlanid, Static Untagged ports

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual show vlan vlanid Purpose Syntax Description Parameters Restrictions Used to display a previously configured VLAN by VLAN ID on the Switch. show vlan vlanid The show VLAN by vlanid command is used to display a previously configured VLAN on the Switch. - Specifies the VID range from the configured VLANs set on the Switch. Only Administrator or Operator-level users can issue this command. Example usage: To display a previously created VLAN: DES-3800:admin#show vlan vlanid 99 Command: show vlan vlanid 99 VID : 99 VLAN Name : robert VLAN TYPE : static Advertisement : Enabled Member ports : 1-4 Static ports : 1-4 Current Tagged ports : 1-4 Current Untagged ports : Static Tagged ports : 1-4 Static Untagged ports : Forbidden ports : Total Entries : 1 DES-3800:admin# config vlan vlanid Purpose Syntax Description Used to add additional ports to a previously configured VLAN. config vlan vlanid {add [ tagged | untagged | forbidden ] | delete | advertisement [enable | disable] | name } The config vlan vlanid command allows you to add or delete ports of the port list of previously configured VLAN(s). You can specify the additional ports as being tagged, untagged or forbidden.The same port is allowed to be an untagged member port of multiple VLAN's. You can also specify if the ports will join GVRP or not with the advertisement parameter. The name parameter allows you to specify the name of the VLAN that needs to be modified. Parameters − Specifies a range of VLAN ID's to add ports to. add − Entering the add parameter will add ports to the VLAN. There are three types of ports to add: • tagged − Specifies the additional ports as tagged. • untagged − Specifies the additional ports as untagged. • forbidden − Specifies the additional ports as forbidden delete- Entering the delete the ports from the VLAN. − A port or range of ports to add to the VLAN. advertisement- Entering the advertisement parameter specifies if the 109

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

109

show vlan vlanid

Purpose

Used to display a previously configured VLAN by VLAN ID on the

Switch.

Syntax

show vlan vlanid

Description

The show VLAN by vlanid

command is used to display a previously

configured VLAN on the Switch.

Parameters

<vidlist> -

Specifies the VID range from the configured VLANs set

on the Switch.

Restrictions

Only Administrator or Operator-level users can issue this command.

Example usage:

To display a previously created VLAN:

DES-3800:admin#show vlan vlanid 99

Command: show vlan vlanid 99

VID

: 99

VLAN Name

: robert

VLAN TYPE

: static

Advertisement : Enabled

Member ports

: 1-4

Static ports

: 1-4

Current Tagged ports

: 1-4

Current Untagged ports :

Static Tagged ports

: 1-4

Static Untagged ports

Forbidden ports :

Total Entries : 1

DES-3800:admin#

config vlan vlanid

Purpose

Used to add additional ports to a previously configured VLAN.

Syntax

config vlan vlanid <vidlist> {add [ tagged | untagged | forbidden ]

| delete

<portlist> | advertisement [enable | disable] | name

<name>}

Description

The config vlan vlanid command allows you to add or delete ports of

the port list of previously configured VLAN(s). You can specify the

additional ports as being tagged, untagged or forbidden.The same

port is allowed to be an untagged member port of multiple VLAN’s.

You can also specify if the ports will join GVRP or not with the

parameter. The

name

parameter allows you to specify

the name of the VLAN that needs to be modified.

Parameters

−

Specifies a range of VLAN ID’s to add ports to.

add

−

Entering the add parameter will add ports to the VLAN. There

are three types of ports to add:

•

tagged

−

Specifies the additional ports as tagged.

•

untagged

−

Specifies the additional ports as untagged.

•

forbidden

−

Specifies the additional ports as forbidden

delete-

Entering the delete the ports from the VLAN.

−

A port or range of ports to add to the VLAN.

advertisement-

Entering the advertisement parameter specifies if the