Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 326

create address_binding ip_mac ipaddress

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 326 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual create address_binding ip_mac ipaddress Purpose Used to create an IP-MAC Binding entry. Syntax create address_binding ip_mac ipaddress mac_address {ports [ | all] | mode {arp | acl]} Description This command will create an IP-MAC Binding entry. Parameters Restrictions The IP address of the device where the IP-MAC binding is made. The MAC address of the device where the IP-MAC binding is made. - Specifies a port or range of ports to be configured for address binding. all - Specifies that all ports on the switch will be configured for address binding. mode - The user may set the mode for this IP-MAC binding settings by choosing one of the following: • arp - Choosing this selection will set a normal IP-MAC Binding entry for the IP address and MAC address entered. If the system is in ARP mode, the arp mode entries and acl mode entries will be effective. If the system is in the acl mode, only the acl mode entries will be active. • acl - Choosing this entry will allow only packets from the source IP-MAC binding entry created here. All other packets with a different IP address will be discarded by the Switch. This mode can only be used if the ACL Mode has been enabled in the IP-MAC Binding Ports window as seen previously. Only Administrator or Operator-level users can issue this command. Example usage: To create address binding on the Switch: DES-3800:admin#create address_binding ip_mac ipaddress 10.1.1.3 mac_address 00-00-00-00-00-04 Command: create address_binding ip_mac ipaddress 10.1.1.3 mac_address 00-00-00-00-00-04 Success. DES-3800:admin# To create address binding on the Switch for ACL mode: DES-3800:admin#create address_binding ip_mac ipaddress 10.1.1.3 mac_address 00-00-00-00-00-04 mode acl Command: create address_binding ip_mac ipaddress 10.1.1.3 mac_address 00-00-00-00-00-04 mode acl Success. DES-3800:admin# Once the ACL mode has been created and enabled (without previously created access profiles), the access profile table will look like this: 322

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

322

create address_binding ip_mac ipaddress

Purpose

Used to create an IP-MAC Binding entry.

Syntax

create address_binding ip_mac ipaddress <ipaddr> mac_address

<macaddr> {ports [<portlist> | all] | mode {arp | acl]}

Description

This command will create an IP-MAC Binding entry.

Parameters

The IP address of the device where the IP-MAC binding is

made.

The MAC address of the device where the IP-MAC binding

is made.

- Specifies a port or range of ports to be configured for

address binding.

all

– Specifies that all ports on the switch will be configured for address

binding.

mode

– The user may set the mode for this IP-MAC binding settings by

choosing one of the following:

•

arp

Choosing this selection will set a normal IP-MAC

Binding entry for the IP address and MAC address entered. If

the system is in ARP mode, the arp mode entries and acl

mode entries will be effective. If the system is in the acl

mode, only the acl mode entries will be active.

•

acl

- Choosing this entry will allow only packets from the

source IP-MAC binding entry created here. All other packets

with a different IP address will be discarded by the Switch.

This mode can only be used if the ACL Mode has been

enabled in the IP-MAC Binding Ports window as seen

previously.

Restrictions

Only Administrator or Operator-level users can issue this command.

Example usage:

To create address binding on the Switch:

DES-3800:admin#create address_binding ip_mac ipaddress

10.1.1.3 mac_address 00-00-00-00-00-04

Command: create address_binding ip_mac ipaddress 10.1.1.3

mac_address 00-00-00-00-00-04

Success.

DES-3800:admin#

To create address binding on the Switch for ACL mode:

DES-3800:admin#create address_binding ip_mac ipaddress

10.1.1.3 mac_address 00-00-00-00-00-04 mode acl

Command: create address_binding ip_mac ipaddress 10.1.1.3

mac_address 00-00-00-00-00-04 mode acl

Success.

DES-3800:admin#

Once the ACL mode has been created and enabled (without previously created access profiles), the access profile table will look like

this: