Home » D-Link Manuals » Hubs & Switches » D-Link DES-3828 » Manual Viewer

D-Link DES-3828 Product Manual - Page 378

config mac_based_access_control, config mac_based_access_control {ports [<portlist> | all] state

UPC - 790069276811

Add to My Manuals
Save this manual to your list of manuals

Page 378 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual config mac_based_access_control Purpose Syntax Description Parameters Restrictions Used to configure the global parameters of the MAC-based Access Control on the Switch. config mac_based_access_control {ports [ | all] state [enable | disable] | method [local | radius] | password } This command is used to configure the global parameters for the MACbased access control function on the Switch, including enabled ports, method of authentication and the password to be used to access the remote RADIUS server. ports - Choose this parameter to configure a list of ports to be enabled for the MAC-based access control function. state [enable | disable] - Use the state parameter to enable or disable the previously set ports as MAC-based access control enabled ports. method - Use this parameter to choose the type of authentication to be used when authenticating MAC addresses on a given port. The user may choose between the following methods: • local - Use this method to utilize the locally set MAC address database as the authenticator for MAC-Based Access Control. This MAC address list can be configured in the MACBased Access Control Local Database Settings window. • radius - Use this method to utilize a remote RADIUS server as the authenticator for MAC-Based Access Control. Remember, the MAC list must be previously set on the RADIUS server and the settings for the server must be first configured on the Switch. password - Use this parameter to enter the password of up to 16 alphanumeric characters for the RADIUS server, which is to be used for packets being sent requesting authentication. The default password is "default". Only Administrator or Operator-level users can issue this command. Example usage: To configure MAC-based Access Control global settings on the Switch. DES-3800:admin#config mac_based_access_control ports 1-8 state enable Command: config mac_based_access_control ports 1-8 state enable Success. DES-3800:admin# 374

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

Match case Limit results 1 per page

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

374

config mac_based_access_control

Purpose

Used to configure the global parameters of the MAC-based Access

Control on the Switch.

Syntax

config mac_based_access_control {ports [<portlist> | all] state

[enable | disable] | method [local | radius] | password <passwd

16>}

Description

This command is used to configure the global parameters for the MAC-

based access control function on the Switch, including enabled ports,

method of authentication and the password to be used to access the

remote RADIUS server.

Parameters

ports <portlist>

- Choose this parameter to configure a list of ports to be

enabled for the MAC-based access control function.

state [enable | disable]

– Use the state parameter to enable or disable

the previously set ports as MAC-based access control enabled ports.

method –

Use this parameter

to choose the type of authentication to be

used when authenticating MAC addresses on a given port. The user

may choose between the following methods:

•

local

– Use this method to utilize the locally set MAC address

database as the authenticator for MAC-Based Access

Control. This MAC address list can be configured in the MAC-

Based Access Control Local Database Settings window.

•

radius

– Use this method to utilize a remote RADIUS server

as the authenticator for MAC-Based Access Control.

Remember, the MAC list must be previously set on the

RADIUS server and the settings for the server must be first

configured on the Switch.

password <passwd 16> -

Use this parameter to enter the password of

up to 16 alphanumeric characters for the RADIUS server, which is to be

used for packets being sent requesting authentication. The default

password is “default”.

Restrictions

Only Administrator or Operator-level users can issue this command.

Example usage:

To configure MAC-based Access Control global settings on the Switch.

DES-3800:admin#config mac_based_access_control ports 1-8 state

enable

Command: config mac_based_access_control ports 1-8 state enable

Success.

DES-3800:admin#