D-Link DES-3828 Product Manual - Page 127

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual

123

17

IGMP

S

NOOPING

C

OMMANDS

The IGMP Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the

following table.

Command

Parameters

config igmp_snooping

[<vlan_name 32> | all] {host_timeout <sec 1-16711450> | router_timeout

<sec 1-16711450> | leave_timer <sec 0-16711450> | state [enable |

disable] | fast_leave [enable | disable]}

config igmp_snooping querier

[<vlan_name 32> | all] {query_interval <sec 1-65535> |

max_response_time <sec 1-25> | robustness_variable <value 1-255> |

last_member_query_interval <sec 1-25> | state [enable | disable]}

config router_ports

<vlan_name 32> [add | delete] <portlist>

enable igmp_snooping

{forward_mcrouter_only}

show igmp_snooping

{vlan <vlan_name 32>}

disable igmp_snooping

{forward_mcrouter_only}

show igmp snooping group

vlan <vlan_name 32>

show router_ports

{vlan <vlan_name 32>} {static | dynamic}

show igmp_snooping forwarding

{vlan <vlan_name 32>}

Each command is listed, in detail, in the following sections.

config igmp_snooping

Purpose

Used to configure IGMP snooping on the Switch.

Syntax

config igmp_snooping [<vlan_name 32> | all] {host_timeout <sec 1-

16711450> | router_timeout <sec 1-16711450> | leave_timer <sec 0-

16711450> | state [enable | disable]} | fast_leave [enable | disable]}

Description

This command allows users to configure IGMP snooping on the Switch.

Parameters

<vlan_name 32>

−

The name of the VLAN for which IGMP snooping is to be

configured.

host_timeout <sec 1-16711450>

−

Specifies the maximum amount of time a

host can be a member of a multicast group without the Switch receiving a

host membership report. The default is 260 seconds.

router_timeout <sec 1-16711450>

−

Specifies the maximum amount of time

a route can be a member of a multicast group without the Switch receiving a

host membership report. The default is 260 seconds.

leave_timer <sec 1-16711450>

−

Specifies the amount of time a Multicast

address will stay in the database before it is deleted, after it has sent out a

leave group message. An entry of zero (0) specifies an immediate deletion

of the Multicast address. The default is 2 seconds.

state [enable | disable]

−

Allows users to enable or disable IGMP snooping

for the specified VLAN.

fast_leave [enable | disable]

– This parameter allows the user to enable the

fast leave

function. Enabled, this function will allow members of a multicast

group to leave the group immediately (without the implementation of the

Last Member Query Timer) when an IGMP Leave Report Packet is received

by the Switch.

Restrictions

Only Administrator or Operator-level users can issue this command.

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443

D-Link DES-3828 Product Manual - Page 127

IGMP Snooping Commands, config igmp_snooping

Page 127 highlights