HP StorageWorks 8/80 HP StorageWorks Fabric OS 6.1.x administrator guide (5697 - Page 342

monitor_class slotnumber portnumber interval The monitor class, which can be one of EE (end-to-end), FLT (filter-based), or ISL (inter-switch link). The --class monitor_class operand is required. Specifies the slot number for a 4/256 SAN Director director. For all other switches, this operand is not required. The slot number must be followed by a slash ( / ) and the port number, so that each port is represented by both slot number (1 through 4 or 7 through 10) and port number (0 through 15). The Directors have a total of 10 slots. Slot numbers 5 and 6 are control processor blades; slots 1 through 4 and 7 through 10 are port blades. For 16-port blades, there are 16 ports, counted from the bottom, numbered 0 to 15. For 32-port blades, there are 32 ports numbered 0 to 31. Specifies a port number. Valid values for port number vary, depending on the switch type. This operand is required. Specifies an interval in seconds. The interval must be greater than or equal to five seconds. For end-to-end monitoring, the Tx and Rx counts are measured in bytes. This operand is optional. The following example displays an end-to-end monitor on a port at 6-second intervals: switch:admin> perfMonitorShow --class EE 4/5 6 perfmonitorshow 53, 6: Tx/Rx are # of bytes and crc is # of crc errors 0 1 2 3 4 crc Tx Rx crc Tx Rx crc Tx Rx crc Tx Rx crc Tx Rx 0 0 0 0 0 00 0 00 0 00 0 0 0 53m 4.9m 0 53m 4.9m 0 53m 4.9m 0 53m 4.9m 0 53m 0 0 53m 4.4m 0 53m 4.4m 0 53m 4.4m 0 53m 4.4m 0 53m 0 0 53m 4.8m 0 53m 4.8m 0 53m 4.8m 0 53m 4.8m 0 53m 0 0 53m 4.6m 0 53m 4.6m 0 53m 4.6m 0 53m 4.6m 0 53m 0 0 53m 5.0m 0 53m 5.0m 0 53m 5.0m 0 53m 5.0m 0 53m 0 0 53m 4.8m 0 53m 4.8m 0 53m 4.8m 0 53m 4.8m 0 53m 0 0 53m 4.5m 0 53m 4.5m 0 53m 4.5m 0 53m 4.5m 0 53m 0 0 52m 4.5m 0 52m 4.5m 0 52m 4.5m 0 52m 4.5m 0 52m 0 0 52m 5.0m 0 52m 5.0m 0 52m 5.0m 0 52m 5.0m 0 52m 0 0 52m 4.5m 0 52m 4.5m 0 52m 4.5m 0 52m 4.5m 0 52m 0 0 52m 4.6m 0 52m 4.6m 0 52m 4.6m 0 52m 4.6m 0 52m 0 The following example displays EE monitors on a port: switch:admin> perfMonitorShow --class EE 4/5 There are 7 end-to-end monitor(s) defined on port 53. KEY SID DID OWNER_APP TX_COUNT CRC_COUNT OWNER_IP_ADDR RX_COUNT 0 0x58e0f 0x1182ef TELNET 0x0000000000000000 0x0000000000000000 0x0000000000000000 N/A 0 0x21300 0x21dda 0x0000000000000000 TELNET 0x00000004d0ba9915 0x0000000067229e65 N/A 1 0x21300 0x21ddc 0x0000000000000000 TELNET 0x00000004d0baa754 0x0000000067229e65 N/A 342 Administering Advanced Performance Monitoring