HP StorageWorks 8/80 HP StorageWorks Fabric OS 6.2 administrator guide (5697-0 - Page 400

used to determine the Area_ID field of the PID) and the Port_ID field. Like the PIDs in a fabric, a proxy PID must be unique. If the slot argument results in a duplicate PID, it will be ignored. Proxy PIDs are automatically assigned to devices imported into a fabric, starting at f001. For Proxy IDs projected to an M-EOS edge fabric in McDATA fabric mode, use valid ALPAs (lower 8 bits). See the fcrProxyConfig command in the Fabric OS Command Reference for more details. Use the fcrXlateConfig command to display or assign a preferred domain ID to a translate domain. See the Fabric OS Command Reference for more details about this command. Fabric parameter considerations By default, EX_Ports and VEX_Ports detect, autonegotiate, and configure the fabric parameters without user intervention. You can, as an option, configure these parameters manually. To change the fabric parameters on a switch in the edge fabric, execute the configure command. To change the fabric parameters of an EX_Port on the FC router, use the portCfgEXPort command. To change the fabric parameters of a VEX_Port, use the portCfgVEXPort command. The backbone fabric PID mode and the edge fabric PID mode do not need to match, but the PID mode for the EX_Port or VEX_Port and the edge fabric to which it is attached must match. You can statically set the PID mode for the fabric by using the -p option with the portCfgEXPort command. Use the -t option to disable the negotiate fabric parameter feature; otherwise, the PID mode is autonegotiated. The various edge fabrics may have different PID modes. Fabric parameter settings, namely, E_D_TOV (error-detect timeout value), R_A_TOV (resource-allocation timeout value), and PID format, must be the same on EX_Ports or VEX_Ports and on the fabrics to which they are connected. You can set the PID format on an EX_Port when you configure an interfabric link. The default values for E_D_TOV and R_A_TOV for an EX_Port or VEX_Port must match those values on other Fabric OS switches. Only if you have adjusted these parameters for the edge fabric do you need to adjust them for an EX_Port or VEX_Port. The default values for R_A_TOV and E_D_TOV are the recommended values for all but very large fabrics (ones requiring four or more hops) or high-latency fabrics (such as ones using long-distance FCIP links). Inter-fabric broadcast frames The FC router can receive and forward broadcast frames between edge fabrics and between the backbone fabric and edge fabrics. Many target devices and HBAs cannot handle broadcast frames. If these devices are connected to switches with Fabric OS 5.3.0 or later, you can set up broadcast zones to control which devices receive broadcast frames. (See "Broadcast zones" on page 241 for information about setting up broadcast zones.) Broadcast zones are supported only on switches running Fabric OS 5.3.0 or later, so all devices that are connected to switches running earlier firmware versions will receive broadcast frames. By default, broadcast frames are forwarded from the FC router to all edge fabrics. You can specify which fabrics should not receive the broadcast frames, thereby preventing the inter-fabric forwarding of broadcast frames to switches running older versions of firmware. For example, in the metaSAN shown in Figure 67 on page 399, Fabric 1 is running a firmware release earlier than 5.3.0. If the devices connected to this fabric do not support broadcast frames, you can disable the forwarding of broadcast frames to Fabric 3. Because all of the switches in Fabric 2 are running Fabric OS 5.3.0 or later, if some of the devices can handle broadcast frames and some cannot, you can create a broadcast zone in this fabric to specify the devices that can handle broadcast frames. Fabric 3 has some switches that are running Fabric OS 5.3.0 and later, and some switches running older firmware versions. In this case, a broadcast zone will not restrict broadcast frames to the devices that are connected to the older switches. You need to decide whether to disable the forwarding of broadcast frames to all the devices in the fabric (using fcrbcastconfig). 398 Using the FC-FC routing service