HP StorageWorks 8/80 HP StorageWorks Fabric OS 6.2 administrator guide (5697-0 - Page 493

The following example shows the results of the performance analysis for slot 8, port ge0: ipperf to 192.41.70.43 from IP interface 192.41.70.42 on 0/1:3227 Sampling frequency(30s) Total time(30s) BW:112.73MBps WBW:55.57MBps Loss(%):0.00 Delay(ms):23 PMTU:1500 Sampling frequency(30s) Total time(60s) BW:112.77MBps WBW:83.61MBps Loss(%):0.00 Delay(ms):23 PMTU:1500 Sampling frequency(30s) Total time(90s) BW:112.43MBps WBW:97.46MBps Loss(%):0.00 Delay(ms):22 PMTU:1500 Sampling frequency(30s) Total time(120s) BW:112.32MBps WBW:104.33MBps Loss(%):0.00 Delay(ms):22 PMTU:1500 Sampling frequency(30s) Total time(150s) BW:112.15MBps WBW:107.69MBps Loss(%):0.00 Delay(ms):23 PMTU:1500 Sampling frequency(30s) Total time(180s) BW:112.54MBps WBW:109.55MBps Loss(%):0.00 Delay(ms):23 PMTU:1500 where: Sampling frequencies The interval specified with the portCmd --ipPerf command with the -i option or the default, 30 seconds. Total Time BW The current running test total time (in seconds) for the last --ipPerf command entered. The bandwidth measured in the last interval. Bandwidth is defined as the total packets and bytes sent. BW represents what the FCIP tunnel / FC application sees for throughput rather than the Ethernet on-the-wire bytes. WBW Loss(%) Delay(ms) PMTU The weighted bandwidth currently with a gain of 50 percent. The number of TCP retransmits. This number is an average rate over the last display interval. The TCP smoothed round-trip time (RTT) and variance estimate in milliseconds. The path MTU. This is the largest IP-layer datagram that can be transmitted over the end-to-end path without fragmentation. This value is measured in bytes and includes the IP header and payload. Note: There is limited support for black hole PMTU detection. If the Jumbo PMTU (anything over 1500) does not work, --ipPerf tries 1500 bytes. If 1500 PMTU fails, --ipPerf tries the lower PMTU of 1260 (the minimum PMTU supported for FCIP tunnels). If 1260 also fails, --ipPerf gives up. There is no support for aging. During black hole PMTU detection the BW, WBW, Loss and PMTU values printed may not be accurate. WAN tool ipPerf syntax When using the portCmd --ipPerf option, you must specify the following: • Source IP address. If the --ipPerf is started with -S (source mode), the port number specified is the remote peer's port number to connect to. • Destination IP address. • Source (transmitter) or sink (receiver). If the --ipPerf is started with -R (sink mode), the port number and source IP address will be used to listen for new connections. If the options are not specified the following defaults apply: • Default port-3227 • Default runtime-forever • Default display (refresh) interval-30 seconds • Default size-1MSS Following is the syntax for portCmd --ipPerf to display end-to-end IP path performance statistics: portCmd --ipPerf [slot]/ge0|ge1 -s source_ip -d destination_ip -S|-R [-r rate] [-z size] [-t time] [-i interval] [-p port] [-q diffserv] [-v vlan_id] [-c L2_Cos] where: -s source_ip The source IP address. -d destination_ipThe destination IP address. Fabric OS 6.2 administrator guide 489