Home » Netgear Manuals » Hubs & Switches » Netgear M4100-26G » Manual Viewer

Netgear M4100-26G CLI Manual - Page 484

IPv6 Access Control List (ACL) Commands, show access-lists

Add to My Manuals
Save this manual to your list of manuals

Page 484 highlights

ProSafe M4100 and M7100 Managed Switches show access-lists This command displays IP ACLs, IPv6 ACLs, and MAC access control lists information for a designated interface and direction. Format Mode show access-lists interface [in|out] Privileged EXEC Term ACL Type ACL ID Sequence Number Definition Type of access list (IP, IPv6, or MAC). Access List name for a MAC or IPv6 access list or the numeric identifier for an IP access list. An optional sequence number might be specified to indicate the order of this access list relative to other access lists already assigned to this interface and direction. A lower number indicates higher precedence order. If a sequence number is already in use for this interface and direction, the specified access list replaces the currently attached access list using that sequence number. If the sequence number is not specified by the user, a sequence number that is one greater than the highest sequence number currently in use for this interface and direction is used. Valid range is (1-4,294,967,295). IPv6 Access Control List (ACL) Commands This section describes the commands you use to configure IPv6 ACL settings. IPv6 ACLs ensure that only authorized users have access to specific resources and block any unwarranted attempts to reach network resources. The following rules apply to IPv6 ACLs: • The maximum number of ACLs you create is 100, regardless of type. • The system supports only Ethernet II frame types. • The maximum number of rules per IPv6 ACL is hardware-dependent. ipv6 access-list This command creates an IPv6 access control list (ACL) identified by , consisting of classification fields defined for the IP header of an IPv6 frame. The parameter is a case-sensitive alphanumeric string from 1 to 31 characters uniquely identifying the IPv6 access list. If an IPv6 ACL by this name exists, this command enters IPv6-Access-List config mode to allow updating the existing IPv6 ACL. Note: The CLI mode changes to IPv6-Access-List Config mode when you successfully execute this command. Quality of Service (QoS) Commands 484

Section	Page
ProSafe Managed Switch	1
Contents	3
1. Using the Command-Line Interface	7
Licensing and Command Support	8
Command Syntax	9
Command Conventions	9
Common Parameter Values	10
Slot/Port Naming Convention	11
Using a Command’s “No” Form	12
Managed Switch Modules	12
Command Modes	12
Command Completion and Abbreviation	16
CLI Error Messages	16
CLI Line-Editing Conventions	17
Using CLI Help	17
Accessing the CLI	18
2. Switching Commands	19
Port Configuration Commands	21
Loopback Interface Commands	27
Spanning Tree Protocol (STP) Commands	30
VLAN Commands	47
Double VLAN Commands	60
Voice VLAN Commands	63
Provisioning (IEEE 802.1p) Commands	65
Protected Ports Commands	65
Private VLAN	68
GARP Commands	71
GVRP Commands	73
GMRP Commands	75
Port-Based Network Access Control Commands	77
802.1X Supplicant Commands	91
Storm-Control Commands	94
Flow Control Commands	104
Port-Channel/LAG (802.3ad) Commands	105
Port Mirroring	121
Static MAC Filtering	123
DHCP L2 Relay Agent Commands	127
DHCP Client Commands	131
DHCP Snooping Configuration Commands	132
Dynamic ARP Inspection Commands	141
IGMP Snooping Configuration Commands	148
IGMP Snooping Querier Commands	157
MLD Snooping Commands	161
MLD Snooping Querier Commands	168
set mld querier	168
set mld querier query_interval	169
set mld querier timer expiry	169
set mld querier election participate	170
show mldsnooping querier	170
Port Security Commands	171
LLDP (802.1AB) Commands	175
LLDP-MED Commands	184
Denial of Service Commands	193
MAC Database Commands	203
ISDP Commands	205
Priority-Based Flow Control Commands	210
3. Multicast VLAN Registration (MVR)	213
About MVR	214
MVR Commands	214
4. Routing Commands	221
Address Resolution Protocol (ARP) Commands	222
IP Routing Commands	227
Router Discovery Protocol Commands	244
Virtual LAN Routing Commands	248
Virtual Router Redundancy Protocol Commands	249
DHCP and BOOTP Relay Commands	257
IP Helper Commands	259
Open Shortest Path First (OSPF) Commands	263
OSPF Graceful Restart Commands	304
nsf	305
nsf restart-interval	305
nsf helper	306
nsf helper disable	307
nsf [ietf] helper strict-lsa-checking	307
OSPF Interface Flap Dampening Commands	309
Routing Information Protocol (RIP) Commands	311
ICMP Throttling Commands	318
5. IP Multicast Commands	321
Multicast Commands	321
DVMRP Commands	326
PIM Commands	331
Internet Group Message Protocol (IGMP) Commands	342
IGMP Proxy Commands	349
6. IPv6 Commands	355
Tunnel Interface Commands	356
IPv6 Routing Commands	357
OSPFv3 Commands	380
OSPFv3 Graceful Restart Commands	411
DHCPv6 Commands	413
7. IPv6 Multicast Commands	421
IPv6 Multicast Forwarder Commands	422
IPv6 PIM Commands	424
IPv6 MLD Commands	431
IPv6 MLD-Proxy Commands	437
8. Quality of Service (QoS) Commands	443
Class of Service (CoS) Commands	444
Differentiated Services (DiffServ) Commands	451
DiffServ Class Commands	452
DiffServ Policy Commands	461
DiffServ Service Commands	466
DiffServ Show Commands	468
MAC Access Control List (ACL) Commands	473
IP Access Control List (ACL) Commands	478
IPv6 Access Control List (ACL) Commands	484
Time Range Commands for Time-Based ACLs	488
AutoVOIP	490
iSCSI Commands	494
9. Power over Ethernet (PoE) Commands	501
About PoE	501
PoE Commands	502
10. Utility Commands	512
Auto Install Commands	513
Dual Image Commands	515
System Information and Statistics Commands	517
Logging Commands	534
Email Alerting and Mail Server Commands	539
System Utility and Clear Commands	546
Simple Network Time Protocol (SNTP) Commands	556
DHCP Server Commands	564
DNS Client Commands	575
Packet Capture Commands	580
Serviceability Packet Tracing Commands	583
Cable Test Command	603
sFlow Commands	604
Software License Commands	609
IP Address Conflict Commands	610
Link Local Protocol Filtering Commands	611
RMON Stats and History Commands	612
UDLD Commands	618
USB commands	620
11. Management Commands	623
Configuring the Switch Management CPU	624
Network Interface Commands	626
Console Port Access Commands	629
Telnet Commands	631
Secure Shell (SSH) Commands	636
Management Security Commands	639
Hypertext Transfer Protocol (HTTP) Commands	640
Access Commands	647
User Account Commands	647
SNMP Commands	670
RADIUS Commands	680
TACACS+ Commands	693
Configuration Scripting Commands	698
Pre-Login Banner and System Prompt Commands	700
Switch Database Management (SDM) Templates	701
IPv6 Management Commands	703
12. Log Messages	708
Core	709
Utilities	711
Management	713
Switching	717
QoS	723
Routing/IPv6 Routing	724
Multicast	727
Stacking	729
Technologies	730
O/S Support	732
13. Green Ethernet Commands	734
Energy-Detect Mode	735
Energy Efficient Ethernet (EEE)	735

Match case Limit results 1 per page

Quality of Service (QoS) Commands

484

ProSafe M4100 and M7100 Managed Switches

show access-lists

This command displays IP ACLs, IPv6 ACLs, and MAC access control lists information for a

designated interface and direction.

Format

show access-lists interface

[in|out]

Mode

ACL Type

ACL ID

Sequence

Number

IPv6 Access Control List (ACL) Commands

This section describes the commands you use to configure IPv6 ACL settings. IPv6 ACLs

ensure that only authorized users have access to specific resources and block any

unwarranted attempts to reach network resources.

The following rules apply to IPv6 ACLs:

•

The maximum number of ACLs you create is 100, regardless of type.

•

The system supports only Ethernet II frame types.

•

The maximum number of rules per IPv6 ACL is hardware-dependent.

ipv6 access-list

This command creates an IPv6 access control list (ACL) identified by

<name>

, consisting of

classification fields defined for the IP header of an IPv6 frame. The

<name>

parameter is a

case-sensitive alphanumeric string from 1 to 31 characters uniquely identifying the IPv6

access list.

If an IPv6 ACL by this name exists, this command enters IPv6-Access-List config mode to

allow updating the existing IPv6 ACL.

Note:

The CLI mode changes to IPv6-Access-List Config mode when you

successfully execute this command.

Privileged EXEC

Term

Definition

Type of access list (IP, IPv6, or MAC).

Access List name for a MAC or IPv6 access list or the numeric identifier for an IP access

list.

An optional sequence number might be specified to indicate the order of this access list

relative to other access lists already assigned to this interface and direction. A lower

number indicates higher precedence order. If a sequence number is already in use for

this interface and direction, the specified access list replaces the currently attached

access list using that sequence number. If the sequence number is not specified by the

user, a sequence number that is one greater than the highest sequence number currently

in use for this interface and direction is used. Valid range is (1–4,294,967,295).