Home » Netgear Manuals » Hubs & Switches » Netgear M4100-26G » Manual Viewer

Netgear M4100-26G CLI Manual - Page 555

Source, Destination, Description, Secure Shell SSH Commands, Hypertext Transfer Protocol

Add to My Manuals
Save this manual to your list of manuals

Page 555 highlights

ProSafe M4100 and M7100 Managed Switches Source nvram:traplog system:running-config {image1 | image2} image1 image2 Destination Description Copies the trap log file to a server. nvram:startup-config Saves the running configuration to nvram. nvram:clibanner Downloads the CLI banner to the system. nvram:script Downloads a configuration script file to the system. During the download of a configuration script, the copy command validates the script. In case of any error, the command lists all the lines at the end of the validation process and prompts you to confirm before copying the script file. nvram:script noval When you use this option, the copy command will not validate the downloaded script file. An example of the CLI command follows: (NETGEAR Switch) #copy tftp://1.1.1.1/file.scr nvram:script file.scr nvram:sshkey-dsa Downloads an SSH key file. For more information, see Secure Shell (SSH) Commands on page 636. nvram:sshkey-rsa1 Downloads an SSH key file. nvram:sshkey-rsa2 Downloads an SSH key file. nvram:sslpem-dhweak Downloads an HTTP secure-server certificate. nvram:sslpem-dhstrong Downloads an HTTP secure-server certificate. nvram:sslpem-root Downloads an HTTP secure-server certificate. For more information, see Hypertext Transfer Protocol (HTTP) Commands on page 640. nvram:sslpem-server Downloads an HTTP secure-server certificate. nvram:startup-config Downloads the startup configuration file to the system. nvram:system-image Downloads a code image to the system. nvram:license-key Download the license date to the system. ias-users Downloads IAS users file by sftp, scp, or tftp {image1 | image2} Download an image from the remote server to either image. In a stacking environment, the downloaded image is distributed to the stack nodes. Upload either image to the remote server. image2 Copy image1 to image2. image1 Copy image2 to image1. Utility Commands 555

Section	Page
ProSafe Managed Switch	1
Contents	3
1. Using the Command-Line Interface	7
Licensing and Command Support	8
Command Syntax	9
Command Conventions	9
Common Parameter Values	10
Slot/Port Naming Convention	11
Using a Command’s “No” Form	12
Managed Switch Modules	12
Command Modes	12
Command Completion and Abbreviation	16
CLI Error Messages	16
CLI Line-Editing Conventions	17
Using CLI Help	17
Accessing the CLI	18
2. Switching Commands	19
Port Configuration Commands	21
Loopback Interface Commands	27
Spanning Tree Protocol (STP) Commands	30
VLAN Commands	47
Double VLAN Commands	60
Voice VLAN Commands	63
Provisioning (IEEE 802.1p) Commands	65
Protected Ports Commands	65
Private VLAN	68
GARP Commands	71
GVRP Commands	73
GMRP Commands	75
Port-Based Network Access Control Commands	77
802.1X Supplicant Commands	91
Storm-Control Commands	94
Flow Control Commands	104
Port-Channel/LAG (802.3ad) Commands	105
Port Mirroring	121
Static MAC Filtering	123
DHCP L2 Relay Agent Commands	127
DHCP Client Commands	131
DHCP Snooping Configuration Commands	132
Dynamic ARP Inspection Commands	141
IGMP Snooping Configuration Commands	148
IGMP Snooping Querier Commands	157
MLD Snooping Commands	161
MLD Snooping Querier Commands	168
set mld querier	168
set mld querier query_interval	169
set mld querier timer expiry	169
set mld querier election participate	170
show mldsnooping querier	170
Port Security Commands	171
LLDP (802.1AB) Commands	175
LLDP-MED Commands	184
Denial of Service Commands	193
MAC Database Commands	203
ISDP Commands	205
Priority-Based Flow Control Commands	210
3. Multicast VLAN Registration (MVR)	213
About MVR	214
MVR Commands	214
4. Routing Commands	221
Address Resolution Protocol (ARP) Commands	222
IP Routing Commands	227
Router Discovery Protocol Commands	244
Virtual LAN Routing Commands	248
Virtual Router Redundancy Protocol Commands	249
DHCP and BOOTP Relay Commands	257
IP Helper Commands	259
Open Shortest Path First (OSPF) Commands	263
OSPF Graceful Restart Commands	304
nsf	305
nsf restart-interval	305
nsf helper	306
nsf helper disable	307
nsf [ietf] helper strict-lsa-checking	307
OSPF Interface Flap Dampening Commands	309
Routing Information Protocol (RIP) Commands	311
ICMP Throttling Commands	318
5. IP Multicast Commands	321
Multicast Commands	321
DVMRP Commands	326
PIM Commands	331
Internet Group Message Protocol (IGMP) Commands	342
IGMP Proxy Commands	349
6. IPv6 Commands	355
Tunnel Interface Commands	356
IPv6 Routing Commands	357
OSPFv3 Commands	380
OSPFv3 Graceful Restart Commands	411
DHCPv6 Commands	413
7. IPv6 Multicast Commands	421
IPv6 Multicast Forwarder Commands	422
IPv6 PIM Commands	424
IPv6 MLD Commands	431
IPv6 MLD-Proxy Commands	437
8. Quality of Service (QoS) Commands	443
Class of Service (CoS) Commands	444
Differentiated Services (DiffServ) Commands	451
DiffServ Class Commands	452
DiffServ Policy Commands	461
DiffServ Service Commands	466
DiffServ Show Commands	468
MAC Access Control List (ACL) Commands	473
IP Access Control List (ACL) Commands	478
IPv6 Access Control List (ACL) Commands	484
Time Range Commands for Time-Based ACLs	488
AutoVOIP	490
iSCSI Commands	494
9. Power over Ethernet (PoE) Commands	501
About PoE	501
PoE Commands	502
10. Utility Commands	512
Auto Install Commands	513
Dual Image Commands	515
System Information and Statistics Commands	517
Logging Commands	534
Email Alerting and Mail Server Commands	539
System Utility and Clear Commands	546
Simple Network Time Protocol (SNTP) Commands	556
DHCP Server Commands	564
DNS Client Commands	575
Packet Capture Commands	580
Serviceability Packet Tracing Commands	583
Cable Test Command	603
sFlow Commands	604
Software License Commands	609
IP Address Conflict Commands	610
Link Local Protocol Filtering Commands	611
RMON Stats and History Commands	612
UDLD Commands	618
USB commands	620
11. Management Commands	623
Configuring the Switch Management CPU	624
Network Interface Commands	626
Console Port Access Commands	629
Telnet Commands	631
Secure Shell (SSH) Commands	636
Management Security Commands	639
Hypertext Transfer Protocol (HTTP) Commands	640
Access Commands	647
User Account Commands	647
SNMP Commands	670
RADIUS Commands	680
TACACS+ Commands	693
Configuration Scripting Commands	698
Pre-Login Banner and System Prompt Commands	700
Switch Database Management (SDM) Templates	701
IPv6 Management Commands	703
12. Log Messages	708
Core	709
Utilities	711
Management	713
Switching	717
QoS	723
Routing/IPv6 Routing	724
Multicast	727
Stacking	729
Technologies	730
O/S Support	732
13. Green Ethernet Commands	734
Energy-Detect Mode	735
Energy Efficient Ethernet (EEE)	735

Match case Limit results 1 per page

Utility Commands

555

ProSafe M4100 and M7100 Managed Switches

nvram:traplog

<url>

Copies the trap log file to a server.

system:running-config

nvram:startup-config

Saves the running configuration to nvram.

<url>

nvram:clibanner

Downloads the CLI banner to the system.

<url>

nvram:script

Downloads a configuration script file to the system.

During the download of a configuration script, the copy

command validates the script. In case of any error, the

command lists all the lines at the end of the validation

process and prompts you to confirm before copying

the script file.

<url>

nvram:script

<destfilename> noval

When you use this option, the copy command will not

validate the downloaded script file. An example of the

CLI command follows:

(NETGEAR Switch) #copy tftp://1.1.1.1/file.scr

nvram:script file.scr

<url>

nvram:sshkey-dsa

Downloads an SSH key file. For more information, see

Secure Shell (SSH) Commands

on page

636.

<url>

nvram:sshkey-rsa1

Downloads an SSH key file.

<url>

nvram:sshkey-rsa2

Downloads an SSH key file.

<url>

nvram:sslpem-dhweak

Downloads an HTTP secure-server certificate.

<url>

nvram:sslpem-dhstrong

Downloads an HTTP secure-server certificate.

<url>

nvram:sslpem-root

Downloads an HTTP secure-server certificate. For

more information, see

Hypertext Transfer Protocol

(HTTP) Commands

on page

640.

<url>

nvram:sslpem-server

Downloads an HTTP secure-server certificate.

<url>

nvram:startup-config

Downloads the startup configuration file to the system.

<url>

nvram:system-image

Downloads a code image to the system.

<url>

nvram:license-key

Download the license date to the system.

<url>

ias-users

Downloads IAS users file by sftp, scp, or tftp

<url>

{image1 | image2}

Download an image from the remote server to either

image. In a stacking environment, the downloaded

image is distributed to the stack nodes.

{image1 | image2}

<url>

Upload either image to the remote server.

image1

image2

Copy

image1

image2

image1

Copy

image2

image1

Source

Destination

Description