Home » Netgear Manuals » Hubs & Switches » Netgear M4100-26G » Manual Viewer

Netgear M4100-26G CLI Manual - Page 89

statistics

Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

ProSafe M4100 and M7100 Managed Switches Term Definition Session Timeout Indicates the time for which the given session is valid. The time period in seconds is returned by the RADIUS server on authentication of the port. This value is valid for the port only when the port control mode is not MAC-based. Session Termination Action This value indicates the action to be taken once the session timeout expires. Possible values are Default, Radius-Request. If the value is Default, the session is terminated the port goes into unauthorized state. If the value is Radius-Request, a reauthentication of the client authenticated on the port is performed. This value is valid for the port only when the port control mode is not MAC-based. The show dot1x detail command will display the following MAC-based dot1x fields if the port-control mode for that specific port is MAC-based. For each client authenticated on the port, the show dot1x detail command will display the following MAC-based dot1x parameters if the port-control mode for that specific port is MAC-based. Term Definition Supplicant The MAC-address of the supplicant. MAC-Address Authenticator PAE State Current state of the authenticator PAE state machine. Possible values are Initialize, Disconnected, Connecting, Authenticating, Authenticated, Aborting, Held, ForceAuthorized, and ForceUnauthorized. Backend Authentication State Current state of the backend authentication state machine. Possible values are Request, Response, Success, Fail, Timeout, Idle, and Initialize. VLAN-Assigned The VLAN assigned to the client by the radius server. Logical Port The logical port number associated with the client. If you use the optional parameter statistics , the following dot1x statistics for the specified port appear. Term Definition Port The interface whose statistics are displayed. EAPOL Frames Received The number of valid EAPOL frames of any type that have been received by this authenticator. EAPOL Frames The number of EAPOL frames of any type that have been transmitted by this Transmitted authenticator. EAPOL Start Frames Received The number of EAPOL start frames that have been received by this authenticator. EAPOL Logoff The number of EAPOL logoff frames that have been received by this authenticator. Frames Received Last EAPOL The protocol version number carried in the most recently received EAPOL frame. Frame Version Switching Commands 89

Section	Page
ProSafe Managed Switch	1
Contents	3
1. Using the Command-Line Interface	7
Licensing and Command Support	8
Command Syntax	9
Command Conventions	9
Common Parameter Values	10
Slot/Port Naming Convention	11
Using a Command’s “No” Form	12
Managed Switch Modules	12
Command Modes	12
Command Completion and Abbreviation	16
CLI Error Messages	16
CLI Line-Editing Conventions	17
Using CLI Help	17
Accessing the CLI	18
2. Switching Commands	19
Port Configuration Commands	21
Loopback Interface Commands	27
Spanning Tree Protocol (STP) Commands	30
VLAN Commands	47
Double VLAN Commands	60
Voice VLAN Commands	63
Provisioning (IEEE 802.1p) Commands	65
Protected Ports Commands	65
Private VLAN	68
GARP Commands	71
GVRP Commands	73
GMRP Commands	75
Port-Based Network Access Control Commands	77
802.1X Supplicant Commands	91
Storm-Control Commands	94
Flow Control Commands	104
Port-Channel/LAG (802.3ad) Commands	105
Port Mirroring	121
Static MAC Filtering	123
DHCP L2 Relay Agent Commands	127
DHCP Client Commands	131
DHCP Snooping Configuration Commands	132
Dynamic ARP Inspection Commands	141
IGMP Snooping Configuration Commands	148
IGMP Snooping Querier Commands	157
MLD Snooping Commands	161
MLD Snooping Querier Commands	168
set mld querier	168
set mld querier query_interval	169
set mld querier timer expiry	169
set mld querier election participate	170
show mldsnooping querier	170
Port Security Commands	171
LLDP (802.1AB) Commands	175
LLDP-MED Commands	184
Denial of Service Commands	193
MAC Database Commands	203
ISDP Commands	205
Priority-Based Flow Control Commands	210
3. Multicast VLAN Registration (MVR)	213
About MVR	214
MVR Commands	214
4. Routing Commands	221
Address Resolution Protocol (ARP) Commands	222
IP Routing Commands	227
Router Discovery Protocol Commands	244
Virtual LAN Routing Commands	248
Virtual Router Redundancy Protocol Commands	249
DHCP and BOOTP Relay Commands	257
IP Helper Commands	259
Open Shortest Path First (OSPF) Commands	263
OSPF Graceful Restart Commands	304
nsf	305
nsf restart-interval	305
nsf helper	306
nsf helper disable	307
nsf [ietf] helper strict-lsa-checking	307
OSPF Interface Flap Dampening Commands	309
Routing Information Protocol (RIP) Commands	311
ICMP Throttling Commands	318
5. IP Multicast Commands	321
Multicast Commands	321
DVMRP Commands	326
PIM Commands	331
Internet Group Message Protocol (IGMP) Commands	342
IGMP Proxy Commands	349
6. IPv6 Commands	355
Tunnel Interface Commands	356
IPv6 Routing Commands	357
OSPFv3 Commands	380
OSPFv3 Graceful Restart Commands	411
DHCPv6 Commands	413
7. IPv6 Multicast Commands	421
IPv6 Multicast Forwarder Commands	422
IPv6 PIM Commands	424
IPv6 MLD Commands	431
IPv6 MLD-Proxy Commands	437
8. Quality of Service (QoS) Commands	443
Class of Service (CoS) Commands	444
Differentiated Services (DiffServ) Commands	451
DiffServ Class Commands	452
DiffServ Policy Commands	461
DiffServ Service Commands	466
DiffServ Show Commands	468
MAC Access Control List (ACL) Commands	473
IP Access Control List (ACL) Commands	478
IPv6 Access Control List (ACL) Commands	484
Time Range Commands for Time-Based ACLs	488
AutoVOIP	490
iSCSI Commands	494
9. Power over Ethernet (PoE) Commands	501
About PoE	501
PoE Commands	502
10. Utility Commands	512
Auto Install Commands	513
Dual Image Commands	515
System Information and Statistics Commands	517
Logging Commands	534
Email Alerting and Mail Server Commands	539
System Utility and Clear Commands	546
Simple Network Time Protocol (SNTP) Commands	556
DHCP Server Commands	564
DNS Client Commands	575
Packet Capture Commands	580
Serviceability Packet Tracing Commands	583
Cable Test Command	603
sFlow Commands	604
Software License Commands	609
IP Address Conflict Commands	610
Link Local Protocol Filtering Commands	611
RMON Stats and History Commands	612
UDLD Commands	618
USB commands	620
11. Management Commands	623
Configuring the Switch Management CPU	624
Network Interface Commands	626
Console Port Access Commands	629
Telnet Commands	631
Secure Shell (SSH) Commands	636
Management Security Commands	639
Hypertext Transfer Protocol (HTTP) Commands	640
Access Commands	647
User Account Commands	647
SNMP Commands	670
RADIUS Commands	680
TACACS+ Commands	693
Configuration Scripting Commands	698
Pre-Login Banner and System Prompt Commands	700
Switch Database Management (SDM) Templates	701
IPv6 Management Commands	703
12. Log Messages	708
Core	709
Utilities	711
Management	713
Switching	717
QoS	723
Routing/IPv6 Routing	724
Multicast	727
Stacking	729
Technologies	730
O/S Support	732
13. Green Ethernet Commands	734
Energy-Detect Mode	735
Energy Efficient Ethernet (EEE)	735

Match case Limit results 1 per page

Switching Commands

ProSafe M4100 and M7100 Managed Switches

The

show dot1x detail <slot/port>

command will display the following MAC-based

dot1x fields if the port-control mode for that specific port is MAC-based. For each client

authenticated on the port, the

show dot1x detail <slot/port>

command will display the

following MAC-based dot1x parameters if the port-control mode for that specific port is

MAC-based.

Supplicant

MAC-Address

Authenticator

PAE State

Backend

Authentication

State

VLAN-Assigned

Logical Port

If you use the optional parameter

statistics

, the following dot1x statistics

for the specified port appear.

Session Timeout

Indicates the time for which the given session is valid. The time period in seconds is

returned by the RADIUS server on authentication of the port. This value is valid for the

port only when the port control mode is not MAC-based.

Session

Termination

Action

This value indicates the action to be taken once the session timeout expires. Possible

values are Default, Radius-Request. If the value is Default, the session is terminated

the port goes into unauthorized state. If the value is Radius-Request, a reauthentication

of the client authenticated on the port is performed. This value is valid for the port only

when the port control mode is not MAC-based.

Term

Definition

The MAC-address of the supplicant.

Current state of the authenticator PAE state machine. Possible values are Initialize,

Disconnected, Connecting, Authenticating, Authenticated, Aborting, Held,

ForceAuthorized, and ForceUnauthorized.

Current state of the backend authentication state machine. Possible values are Request,

Response, Success, Fail, Timeout, Idle, and Initialize.

The VLAN assigned to the client by the radius server.

The logical port number associated with the client.

Term

Definition

Port

The interface whose statistics are displayed.

EAPOL Frames

Received

The number of valid EAPOL frames of any type that have been received by this

authenticator.

EAPOL Frames

Transmitted

The number of EAPOL frames of any type that have been transmitted by this

authenticator.

EAPOL Start

Frames

Received

The number of EAPOL start frames that have been received by this authenticator.

EAPOL Logoff

Frames

Received

The number of EAPOL logoff frames that have been received by this authenticator.

Last EAPOL

Frame Version

The protocol version number carried in the most recently received EAPOL frame.

Term

Definition