Sony MLS-X1 Users Guide - Page 135
Selecting a DME Channel Key, Control Block, Using two to four DME channels on a, single key
View all Sony MLS-X1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 135 highlights
1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key > Resizer Adjust/DME Select menu (11101.41). 2 In the [DME Select] group, select a DME channel (DME 1 to DME 4) to assign. You can check the DME channel status using the button display. On: DME channel assigned to the selected key Off: DME channel not assigned Lock icon: DME channel assigned to a different key/ bus To select a DME channel assigned to a different key or bus Use the override function. You can release the DME channel assignment for another key/bus and then select the DME channel. To enable the override function, set the [Override] button to the on state. The DME channel is assigned to the selected key and the lock icon displayed on the DME channel button disappears. Using two to four DME channels on a single key You can select multiple consecutive DME channels. 1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key > Resizer Adjust/DME Select menu (11101.41). 2 In the [DME Select] group, select a DME channel (DME 1 to DME 4) to assign. When using two DME channels Set the [DME 1] button and [DME 2] button, the [DME 2] button and [DME 3] button, or the [DME 3] button and [DME 4] button to the on state. When using three DME channels Set the [DME 1] button, [DME 2] button, and [DME 3] button, or the [DME 2] button, [DME 3] button, and [DME 4] button to the on state. When using four DME channels Set the [DME 1] button, [DME 2] button, [DME 3] button, and [DME 4] button to the on state. Selecting a DME channel signal Select the following signals on the 1st channel to 4th channel. For details about selecting a signal, see "Chapter 4 Selecting Signals" (page 81). 1st channel signal: Key bus signal 2nd channel signal: DME external video bus signal 3rd channel signal: DME utility 1 bus signal 4th channel signal: DME utility 2 bus signal Assigning to DME monitor outputs 1 Open the Home > M/E-1 > Key1 > Resizer/Proc Key > Monitor menu (11101.44). 2 Set the [Monitor Set] button to the on state. 3 In the [DME Select] group, select a DME channel (DME 1 to DME 4) to assign. Only DME channels assigned to the selected key can be selected. The output of the selected DME channel is assigned to the monitor output (DME MON V and DME MON K), and the [Monitor Set] button switches to the off state. Selecting a DME Channel (Key Control Block) This section describes an example using a DME on key 1 on M/E-1. 1 Press the [M/E-1] button, turning it on. 2 Press the [KEY1] button, turning it on. 3 Select a DME channel to assign using the DME channel selection buttons (DME1 to DME4). You can check the DME channel status using the lit color of the [DME1] button to [DME4] button. Lit green: DME channel assigned to the selected key Off: DME channel not assigned Lit amber: DME channel assigned to a different key/ bus To select a DME channel assigned to a different key or bus Use the override function. You can release the DME channel assignment for another key/bus and then select the DME channel. To enable the override function, press and hold the [OVERRIDE] button and press a DME channel selection button that is lit amber. The DME channel is assigned to the selected key and the color of the DME channel selection button changes to green. Using two to four DME channels on a single key You can select multiple consecutive DME channels. 135