Sony MLS-X1 Users Guide - Page 166
Frame I/O 2-channel mode pattern numbers, to 2864, Brick 3-channel mode pattern number 3601, Direction
View all Sony MLS-X1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 166 highlights
Frame I/O (2-channel mode) pattern numbers 2861 to 2864 No. Parameter 1 Rot X 2 Rot Y 3 Rot Z 5 Delay Adjustment Rotation around Y-axis (rotation in horizontal direction) Rotation around X-axis (rotation in vertical direction) Rotation around Z-axis Timing for image selected on a utility bus to enter the frame Brick (3-channel mode) pattern number 3601 No. Parameter Adjustment 1-1 Side V Size X Side V horizontal scaling factor 1-2 Side V Size Y Side V vertical scaling factor 1-3 Height Height of brick a) 1-4 Side V Center X Side V horizontal center position b) 1-5 Side V Center Y Side V vertical center position c) 2-1 Side H Size X Side H horizontal scaling factor 2-2 Side H Size Y Side H vertical scaling factor 2-3 Height Height of brick a) 2-4 Side H Center X Side H horizontal center position b) 2-5 Side H Center Y Side H vertical center position c) a) The [Height] parameter in numbers 1-3 and 2-3 are common. b) Side V/side H image horizontal center position. At -100.00, the center is at the left edge of the screen. At +100.00, the center is at the right edge of the screen. c) Side V/side H image vertical center position. At -100.00, the center is at the bottom edge of the screen. At +100.00, the center is at the top edge of the screen. Setting Modifiers You can add modifiers to modify a DME wipe pattern. Direction Sets the direction of travel of the DME wipe. Notes • The direction cannot be set for the following patterns. - Frame I/O pattern numbers 1201, 1202, 1203, 1205, 1206, 1208, 1209, 1225 - P in P pattern number 1251 - Mosaic pattern number 1701 - Defocus pattern number 1702 • In a key DME wipe, the direction can be set for the following patterns. - Frame I/O pattern numbers 1204, 1207, 1221 to 1224 - Resizer Frame I/O pattern numbers 7204, 7207, 7221 to 7224 Edge Adds a border to a DME wipe pattern. Note The edges cannot be set for the following patterns. • Split pattern numbers 1011, 1012, 1013 • Mosaic pattern number 1701 • Defocus pattern number 1702 Position You can move a DME wipe pattern to a desired position. You can move to a specified position (upper left, upper right, bottom left, bottom right) using Position Select. The position can be set for the following patterns. The target position and movement varies depending on the pattern. • Squeeze pattern number 1031 Resizer Squeeze pattern number 7031 As the transition progresses, the pattern center automatically moves from the initial set position toward the center of the screen. • Squeeze pattern numbers 1032, 1033 You can set the pattern position at the start of the transition. As the transition progress resumes after the dead band, the pattern automatically moves from the initial position toward the center of the screen. • Frame I/O pattern numbers 1201 to 1209, 1221 to 1225 P in P pattern number 1251 Resizer Frame I/O pattern numbers 7201 to 7208, 7221 to 7224 You can set the pattern position at the end of the first transition. • P in P pattern numbers 2651, 2652 You can configure each channel separately, or configure two channels simultaneously, depending on their relative positions. • Brick pattern numbers 2801 to 2804, 2811 to 2814 You can set the vertical position where the brick slides in. • Frame I/O pattern numbers 2851 to 2854, 2861 to 2864 You can set the pattern position at the end of the first transition for each channel. Size Sets the size of a DME wipe pattern. Note The size can be set for the following patterns. • Frame I/O pattern numbers 1201 to 1209, 1221 to 1225, 2851 to 2854, 2861 to 2864 • P in P pattern numbers 1251, 2651, 2652 • Resizer Frame I/O pattern numbers 7201 to 7208, 7221 to 7224 Crop Crops the top, bottom, left, right sides of a DME wipe pattern. 166