Sony MLS-X1 Users Guide - Page 410
Setting Utility Bus Mode, Setting a Cross-Point Pad, Assigning functions to a cross-point pad, button
View all Sony MLS-X1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 410 highlights
Select a tab to change the switcher bank/AUX bus control block (AUX 1, AUX 2) to display. 3 Select the target display mode (1 to 6) to set. 4 Split the display using the [Split] switch. On: Split the display into two (upper and lower areas). Off: Do not split the display. 5 Select the items to display. When the [Split] switch is set to the on position Press the [Upper Area] button and select an item to display in the upper area from the pull-down list. Press the [Lower Area] button and select an item to display in the lower area from the pull-down list. When the [Split] switch is set to the off position Press the [Lower Area] button and select an item to display from the pull-down list. To make the display background gray Set the [Gray Bkgd] switch to the on state. To set a display mode name You can set the display mode name to display on buttons in the cross-point pad in the cross-point control block/ AUX bus control block on the ICP-X7000. Press the [Name] button and enter a display mode name (up to 12 characters) using the keyboard. Note Characters entered in lower case are all displayed in upper case when displayed on the cross-point pad buttons. To return the settings to the defaults Press the [Default Recall] button, check the message, then press [OK]. Setting Utility Bus Mode In utility bus mode, you can set the bus assigned to the 1st row to 4th row in the cross-point control block. For details about utility bus mode, see "Utility bus mode" (page 86). 1 Open the Home > Setup > Panel > Xpt Module > Util Button Bus Assign menu (19104.35). 2 Display the target switcher bank to set. Select a tab to change the switcher bank to display. A list of button rows is shown on the left and a list of assignable buses is shown on the right. 3 In the list on the left, select the target button row (1 to 4) to set. 4 In the list on the right, select a bus to assign. 5 Press the [Set] button. To release the assignment In the list on the left, select the target button row (1 to 4) to release and press the [Clear] button. To return the assignment to the defaults Press the [Default Recall] button, check the message, then press [OK]. Setting a Cross-Point Pad You can set the buttons in the cross-point pad in the crosspoint control block/AUX bus control block on the ICP-X7000. Assigning functions to a cross-point pad button You can assign a different function to a button on each of the 14 pages for the cross-point pad. 1 Open the Home > Setup > Panel > Xpt Module > Xpt Pad Button Assign menu (19104.36). 2 In the [Select Bank] group, select the target switcher bank/AUX bus control block (AUX 1, AUX 2) to set. Place a check mark for the switcher bank/AUX bus control block to select. You can also select multiple switcher banks/AUX bus control blocks and set cross-point pad buttons simultaneously. Notes • A switcher bank and AUX bus control block cannot be selected simultaneously. • When multiple switcher banks/AUX bus control blocks are selected, the last selected switcher bank/ AUX bus control block becomes the reference and is displayed highlighted. The button names configured on the reference switcher bank/AUX bus control block are displayed on the cross-point pad buttons. When the reference switcher bank is deselected, the reference will be set according to the following order of priority. M/E-1 > M/E-2 > M/E-3 > M/E-4 > M/E-5 > P/P • In multi program 2 mode, main and sub can be set separately. When a switcher bank is set to shared main and sub, the button assignments are also shared. 410