Sony MLS-X1 Users Guide - Page 237

Setting control panel buttons when sharing main and sub You can assign the main/sub switching buttons ([MAIN] button and [SUB] button) to the cross-point control block, transition control block, and transition control block (simple type). For details about assigning buttons, see "Assigning Control Panel Buttons" (page 402) and "Setting a CrossPoint Pad" (page 410). To switch operation to the main side, press the [MAIN] button, turning it on. To switch operation to the sub side, press the [SUB] button, turning it on. To operate main and sub simultaneously, press both the [MAIN] button and [SUB] button, turning them on. Note Switch between main and sub after a transition has completed. Recalling a snapshot/effect timeline You can also include the operation mode configuration data when recalling a snapshot or effect timeline. For details about settings, see "Setting the recall target for an effect timeline/snapshot" (page 389). Note You can also automatically change the operation mode configuration data saved in a register when copy/move/ swap operations are performed between main and sub registers. For details about settings, see "Changing main/sub configuration data in multi program 2 mode" (page 276) and "Changing main/sub configuration data in multi program 2 mode" (page 288). To change program output key assignments When a snapshot or effect timeline is recalled on main or sub, only the keys being used on main and sub, according to the operation mode configuration data of the switcher bank, become the recall target. When [Recall M/E Config] is enabled in the Home > Setup > Switcher > Config > M/E Config menu (19103.12), you can also change the key assignment in the Common > Key Priority/Key Assign menu of the switcher bank. This section describes the M/E-1 menu as an example. Note The key assignment is linked to the Home > Setup > Switcher > Config > PGM Config menu (19103.13) settings. 1 Open the Home > M/E-1 > Common > Key Priority/ Key Assign menu (11110.11). The key assignment status of the program 1 output to program 4 output are shown at the bottom. 2 Select the target program output (PGM1 to PGM4) to set. 3 Press the [Edit] button. The [Enable Key] window appears. 4 Place a check mark in the keys to enable. Notes • SL keys 5 to 8 are enabled/disabled as a group. • SL keys are disabled for PGM2 to PGM4. 5 Press [OK]. Settings and functions added in multi program 2 mode • Sub switcher bank menus (M/E-1 Sub to M/E-5 Sub, P/P Sub) are added. • The sub switcher banks (M/E-1 Sub to M/E-5 Sub, P/P Sub) are added to the menu as setup targets. • Sub switcher bank regions (M/E-1 Sub to M/E-5 Sub, P/P Sub) are added. • Main and sub switcher banks and keys are shown on the transition control block display. Switcher banks: MAIN (dedicated main), SUB (dedicated sub), MAIN&SUB (shared main and sub) Keys: M (key assigned to main), S (key assigned to sub) • The main and sub assignment status (MAIN, SUB, M&S) is displayed on the switcher bank name display buttons in the cross-point pad • The [SUB TRANS] button in the key control block can be used. • Utility 2 bus selection on the sub side is supported using the delegation buttons in the AUX bus control block • When extended re-entry is enabled for switcher banks, re-entry signals within the main switcher bank, within the sub switcher bank, and between main and sub switcher banks can be selected. For details about extended re-entry, see "Setting Extended Re-Entry" (page 390). • "Sub" and "Main&Sub" settings are added to macro event parameters and macro attachment list buttons. For details about macro events, see "Macro Events" (page 517). For details about macro attachment lists, see "Macro Attachment Lists" (page 525). • Sub switcher bank preview is added to the utility commands. For details about utility commands, see "List of Utility Commands" (page 232). 237