Sony MLS-X1 Users Guide - Page 165
Setting a DME Wipe, Setting a DME Wipe Pattern
View all Sony MLS-X1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 165 highlights
Setting a DME Wipe DME wipe patterns and modifiers are configured using the menu. This section describes the M/E-1 menu as an example. Setting a DME Wipe Pattern Selecting a DME wipe pattern 1 Open the DME wipe pattern selection menu. In 1-channel mode, open the Home > M/E-1 > Bus/ Transition > DME Wipe > 1ch Pattern menu (11109.41). In 2-channel mode, open the Home > M/E-1 > Bus/ Transition > DME Wipe > 2ch Pattern menu (11109.42). In 3-channel mode, open the Home > M/E-1 > Bus/ Transition > DME Wipe > 3ch Pattern menu (11109.43). 2 Press the button for a DME wipe pattern group. The patterns in the selected group are displayed. For 1-channel mode Select from the following DME wipe pattern groups. Slide / Squeeze: Slide and squeeze Split / Door: Split and door Flip Tumble: Flip tumble Page Turn: Page turn Roll: Roll Frame I/O / P in P: Frame in/out and picture-in- picture Mosaic / Defocus: Mosaic and defocus Resizer Slide / Squeeze: Resizer slide and squeeze Resizer Frame I/O: Resizer frame in/out For 2-channel mode Select from the following DME wipe pattern groups. Slide / Squeeze: Slide and squeeze P in P: Picture-in-picture Crop Slide: Crop slide Page Turn: Page turn Roll: Roll Frame I/O: Frame in/out Brick: Brick For 3-channel mode Select from the following DME wipe pattern groups. Brick: Brick 3 Set the button for the target DME wipe pattern to the on state. Adjusting DME wipe pattern parameters When the following patterns are selected, set the parameters. Squeeze (1-channel mode) pattern numbers 1032, 1033 Crop Slide (2-channel mode) pattern numbers 2661, 2662 No. Parameter 1 Holding Level 2 Tolerance Adjustment Position for entering the dead band a) Width of the dead band a) Set relative to a transition start point of 0% and end point of 100%. Page Turn (1-channel mode) pattern numbers 1301 to 1313, 1315 to 1318, 1341 to 1345 Page Turn (2-channel mode) pattern numbers 2701 to 2713, 2715 to 2718, 2741 to 2745 Roll (1-channel mode) pattern numbers 1321 to 1333, 1335 to 1338, 1346 to 1350 Roll (2-channel mode) pattern numbers 2721 to 2733, 2735 to 2738, 2746 to 2750 No. Parameter 1 Radius 2 Magnitude 3 Start Angle Adjustment Radius of the turned page flap/ rolled-up portion a) Angle of rotation through course of transition b) Angle at start of transition b) a) 0% is an effect like a turned page, 100% is normal curl, and 200% is radius with double the normal curl. b) -100.00 is rotation in the counterclockwise direction, +100.00 is rotation in the clockwise direction, and 0.00 is no rotation. Brick (2-channel mode) pattern numbers 2801 to 2804, 2811 to 2814 No. Parameter 1 Side V Size X 2 Side V Size Y 3 Height 4 Center X 5 Center Y Adjustment Side V horizontal scaling factor Side V vertical scaling factor Height of brick Horizontal center position a) Vertical center position b) a) Side V image horizontal center position. At -100.00, the center is at the left edge of the screen. At +100.00, the center is at the right edge of the screen. b) Side V image vertical center position. At -100.00, the center is at the bottom edge of the screen. At +100.00, the center is at the top edge of the screen. Frame I/O (2-channel mode) pattern numbers 2851 to 2854 No. Parameter 1 Delay Adjustment Timing for image selected on a utility bus to enter the frame 165