Home » Netgear Manuals » Hubs & Switches » Netgear XCM8810 Chassis » Manual Viewer

Netgear XCM8810 Chassis Hardware Installation Guide - Page 266

Powered OFF, The display also includes a notice of insufficient power, should that arise.

View all Netgear XCM8810 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 266 highlights

NETGEAR 8800 Chassis Switch CLI Manual • The number of ports on the module • The current number of times the module has been restarted after a failure and the configured restart-limit. Note: You may see slightly different information displayed depending on the platform and configuration you are using. If you do not specify a slot number, information for all slots is displayed. The display also includes a notice of insufficient power, should that arise. The show slot command displays the following states, among others: • Empty (This is also displayed if you have a module in the chassis that is unsupported by the current software you are running.) • Down • Power ON • Powered OFF • Booting • Initializing • VLAN sync • FDB sync • ACL sync • RT sync • Operational The following example displays module information for all slots: Slots Type Configured State Ports Flags Slot-1 Empty 0 Slot-2 XCM8824F XCM8824F Operational 24 M S Slot-3 Empty 0 Slot-4 Empty 0 Slot-5 XCM8808X XCM8808X Operational 8 M S Slot-6 Empty 0 Slot-7 XCM8848T Empty 48 Slot-8 XCM8848T Operational 48 M S Slot-9 XCM8808X XCM8808X Powered OFF 8 SI Slot-10 Empty 0 MSM-A XCM88S1 Operational 0 S MSM-B Empty 0 Flags : M - Backplane link to Master MSM is Active 266 | Chapter 5. Commands for Configuring Slots and Ports on a Switch

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345