Home » Netgear Manuals » Hubs & Switches » Netgear XCM8810 Chassis » Manual Viewer

Netgear XCM8810 Chassis Hardware Installation Guide - Page 811

VRRP Commands, NETGEAR 8800 Chassis Switch CLI Manual

View all Netgear XCM8810 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 811 highlights

NETGEAR 8800 Chassis Switch CLI Manual show vrrp virtual-router show vrrp virtual-router Description Displays the VRRP that matches the specified virtual router. Syntax Description vr-name Specifies the name of the virtual router Default N/A Usage Guidelines The command displays the VRRP information only for a specific virtual router on the device. If you do not specify a virtual router (refer to show vrrp virtual-router), all VRRP virtual routers on this device are displayed. This displays the following VRRP information: • VLAN Name-The name of the VRRP VLAN and whether VRRP is enabled or disabled on the VLAN. The enable/disable state appears as follows: • En-VRRP is enabled on this VLAN. • Ds-VRRP is disabled on this VLAN. • VRID-The VRRP Virtual Router Identification number for the VRRP VLAN. • Pri-The priority value of the VRRP VLAN. • Virtual IP Addr-If configured, the virtual IP address associated with the VRRP VLAN. • State-The current state of the VRRP router. The state includes the following: • Init-The VRRP router is in the initial state. • Backup-The VRRP router is a backup router. • Master-The VRRP router is the master router. • Master Mac Address-The MAC address of the master VRRP router. • TP-Indicates the number of tracked pings. • TR-Indicates the number of tracked routes. • TV-Indicates the number of tracked VLANs. • P-Indicates that the VRRP VLAN is configured for preempt mode, which controls whether a higher priority backup router preempts a lower priority master. • T-Indicates the configured advertisement interval. Chapter 18. VRRP Commands | 811

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345