Home » Netgear Manuals » Hubs & Switches » Netgear XCM8810 Chassis » Manual Viewer

Netgear XCM8810 Chassis Hardware Installation Guide - Page 752

con stpd hellotime, con stpd maxage

View all Netgear XCM8810 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 752 highlights

NETGEAR 8800 Chassis Switch CLI Manual You should not configure any STP parameters unless you have considerable knowledge and experience with STP. The default STP parameters are adequate for most networks. The range for the parameter is 4 through 30 seconds. Example The following command sets the forward delay from STPD1 to 20 seconds: configure stpd stpd1 forwarddelay 20 configure stpd hellotime configure stpd hellotime Description Specifies the time delay (in seconds) between the transmission of BPDUs from this STPD when it is the root bridge. Syntax Description stpd_name seconds Specifies an STPD name on the switch. Specifies the hello time in seconds. The default is 2 seconds, and the range is 1 to 10 seconds. Default The default hello time is 2 seconds. Usage Guidelines If your STPD has the same name as another component, for example a VLAN, NETGEAR recommends that you specify the identifying keyword as well as the name. If your STPD has a name unique only to that STPD, the keyword stpd is optional. In an MSTP environment, configure the hello timer only on the CIST, not on the MSTIs. You should not configure any STP parameters unless you have considerable knowledge and experience with STP. The default STP parameters are adequate for most networks. The range for the parameter is 1 through 10 seconds. Example The following command sets the time delay from STPD1 to 10 seconds: configure stpd stpd1 hellotime 10 configure stpd maxage configure stpd maxage 752 | Chapter 17. STP Commands

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345