Home » Netgear Manuals » Hubs & Switches » Netgear XCM8810 Chassis » Manual Viewer

Netgear XCM8810 Chassis Hardware Installation Guide - Page 782

D Disable-The STPD is disabled.

View all Netgear XCM8810 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 782 highlights

NETGEAR 8800 Chassis Switch CLI Manual Description Displays STPD settings on the switch. Syntax Description stpd_name detail Specifies an STPD on the switch. Specifies that STPD settings should be shown for each STPD. Default N/A. Usage Guidelines If you specify the command without any options, the following STPD information appears: • Name-The name of the STPD. • Tag-The StpdID of the domain, if configured. • Flags-The following flags communicate information about the current state of the STPD: • (C) Topology Change-A network topology change has occurred in the network. • (D) Disable-The STPD is disabled. • (E) Enable-The STPD is enabled. • (R) Rapid Root Failover-The STPD has been configured for rapid root failover • (T) Topology Change Detected-The STPD has detected a change in the network topology. • (M) MSTP CIST-The STPD has been configured for MSTP, and the STPD is the common and internal spanning tree. • (I) MSTP MSTI-The STPD has been configured for MSTP, and the STPD is a multiple instance spanning tree. • Ports-The number of ports that are part of the STPD. • Bridge ID-The MAC addresses of the switch. • Designated Root-The MAC address of the switch that is the designated root bridge. • Rt Port-The root port. • Rt Cost-The path cost to the root port. • Total Number of STPDs-The total number of STPDs configured on the switch. If you have an MSTP region and associated spanning trees configured on the switch, the command also displays the following global MSTP information: • MSTP Region-The name of the MSTP region configured on the switch. • Format Identifier-The number used by BPDUs to communicate within an MSTP region. • Revision Level-This number is reserved for future use. 782 | Chapter 17. STP Commands

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345