Home » Netgear Manuals » Hubs & Switches » Netgear XCM8810 Chassis » Manual Viewer

Netgear XCM8810 Chassis Hardware Installation Guide - Page 490

con access-list add

View all Netgear XCM8810 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 490 highlights

NETGEAR 8800 Chassis Switch CLI Manual Example The following command configures the ACL policy test to port 1:2 at ingress: configure access-list test ports 1:2 The following command configures the ACL mydefault as the wildcard ACL: configure access-list mydefault any The following command configures the ACL policy border as the wildcard egress ACL: configure access-list border any egress configure access-list add configure access-list add [ [[first | last] {priority } {zone } ] | [[before | after] ] | [ priority {zone } ]] [ any | vlan | ports ] {ingress | egress} Description Configures a dynamic ACL rule to the specified interface and sets the priority and zone for the ACL. Syntax Description dynamic_rule first last zone p_number before after any vlanname portlist ingress egress Specifies a dynamic ACL rule. Specifies that the new dynamic rule is to be added as the first rule. Specifies that the new dynamic rule is to be added as the last rule. Specifies the ACL zone for the rule. Specifies the priority number of the rule within a zone. The range is from 0 (highest priority) to 7 (lowest priority). Specifies that the new dynamic rule is to be added before an existing dynamic rule. Specifies that the new dynamic rule is to be added after an existing dynamic rule. Specifies that this ACL is applied to all interfaces. Specifies the VLAN on which this ACL is applied. Specifies the ports on which this ACL is applied. Apply the ACL to packets entering the switch on this interface. Apply the ACL to packets leaving the switch from this interface. Default The default direction is ingress. 490 | Chapter 13. ACL Commands

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345