Home » Netgear Manuals » Hubs & Switches » Netgear GS418TPP » Manual Viewer

Netgear GS418TPP User Manual - Page 221

Adv Managed Config Flag

Add to My Manuals
Save this manual to your list of manuals

Page 221 highlights

ProSAFE 8-Port or 16-Port Gigabit Smart Managed Switch Model GS418TPP, GS510TLP, and GS510TPP 14. In the Adv NS Interval field, specify the retransmission time field of router advertisements sent from the interface. A value of 0 means the interval is not specified for the router. The range of the neighbor solicit interval is 1000 to 4294967295. The default is 0. 15. In the Adv Reachable Interval field, specify the router advertisement time. This is the time allocated to consider the neighbors reachable after ND confirmation. The range of reachable time is 0 to 3600000. The default is 0. 16. In the Adv Interval field, specify the maximum time allowed between sending router advertisements from the interface. The range of the maximum advertisement interval is 4 to 1800. The default value is 600. 17. From the Adv Managed Config Flag menu, specify the setting for the router advertisement managed address configuration flag. When the selection is Enable, end nodes use DHCPv6. When the selection is Disable, end nodes autoconfigure addresses. The default value is Disable. 18. From the Adv Other Config Flag menu, select to enable or disable the router advertisement other stateful configuration flag. The default value is Disable. 19. From the Router Preference menu, specify the router preference advertisement on an interface. The default value is Medium. 20. From the Adv Suppress Flag menu, select to enable or disable the router advertisement suppression on an interface. The default value is Disable. 21. From the Destination Unreachables menu, select to enable or disable the mode for sending ICMPv6 destination unreachable messages on this interface. If this mode is disabled, the interface does not send ICMPv6 destination unreachable messages. By default, the IPv6 destination unreachables mode is enabled. 22. Click the Apply button. The updated configuration is sent to the switch. Configuration changes take effect immediately. The following table describes the nonconfigurable data that is displayed. Table 60. IPv6 VLAN Configuration information Field Routing Mode Operational Mode Link State Description The routing mode of an interface. The default is Disable. The operational state of an interface. The default value is Disable. Indicates whether the link is up or down. Configure Routing 221

Section	Page
ProSAFE 8-Port or 16-Port Gigabit Smart Managed Switch with PoE+ and 2 SFP Ports	1
Contents	3
1. Get Started	10
Switch Management Interface Overview	11
Change the Default IP Address of the Switch	11
Discover a Switch in a Network With a DHCP Server	12
Discover a Switch in a Network Without a DHCP Server	13
Configure the Network Settings on Your Computer	14
Access the Web Browser–Based Management Interface	17
About the User Interfaces	17
Software Requirements to Use the Web Interface	17
Supported Web Browsers	18
Use a Web Browser to Access the Switch and Log In	18
Navigation Tabs, Configuration Menus, and Page Menu	19
Configuration and Status Options	20
Web Interface Buttons	20
User-Defined Fields	21
Web Browser–Based Management Interface Device View	21
Power LED	23
Fan LED	23
Interface Naming Conventions	23
Configure Interface Settings	24
Context-Sensitive Help and Access to the Support WebSite	28
User Guide	29
Register Your Product	29
2. Configure System Information	30
View and Configure the Switch Management Settings	31
View or Define System Information	31
View the System CPU Status	36
View USB Device Information	39
IP Configuration	40
IPv6 Network Configuration	42
View the IPv6 Network Neighbor	43
Configure the Time Settings	44
Configure Denial of Service Settings	60
Configure DNS Settings	63
Configure Green Ethernet Settings	67
Use the Device View	75
Configure PoE	75
Configure the Global PoE Settings	75
Configure the PoE Port Settings	77
Configure SNMP	80
Configure the SNMPv1/v2 Community	80
Configure SNMPv1/v2 Trap Settings	83
Configure SNMPv1/v2 Trap Flags	85
View the Supported MIBs	86
Configure SNMP V3 Users	87
Configure LLDP	88
Configure LLDP Global Settings	89
Configure LLDP Port Settings	90
LLDP-MED Network Policy	91
LLDP-MED Port Settings	93
Local Information	94
Neighbors Information	96
Configure DHCP L2 Relay, DHCP Snooping, and Dynamic ARP Inspection	99
DHCP L2 Relay	100
DHCP Snooping	103
Dynamic ARP Inspection	110
Set Up PoE Timer Schedules	118
Create a PoE Timer Schedule	119
Specify the Settings for an Absolute PoE Timer Schedule	119
Specify the Settings for a Recurring PoE Timer Schedule	120
Change the Settings for a Recurring PoE Timer Schedule Entry	122
Delete a PoE Timer Schedule Entry	123
Delete a PoE Timer Schedule	124
3. Configure Switching	125
Configure Port Settings	126
Configure Link Aggregation Groups	128
Configure LAG Settings	129
Configure LAG Membership	131
Set the LACP System Priority	132
Set the LACP Port Priority Settings	133
Configure VLANs	134
Configure VLAN Settings	134
Configure VLAN Membership	137
View VLAN Status	139
Configure Port PVID Settings	140
Configure a MAC-Based VLAN	142
Configure Protocol-Based VLAN Groups	144
Configure Protocol-Based VLAN Group Membership	145
Configure a Voice VLAN	147
Configure GARP Switch Settings	148
Configure GARP Ports	150
Configure Auto-VoIP	151
Configure Protocol-Based Port Settings	151
Configure Auto-VoIP OUI-Based Properties	153
OUI-Based Port Settings	154
Manage the OUI Table	155
Display the Auto-VoIP Status	157
Configure Spanning Tree Protocol	158
Configure STP Settings	159
Configure CST Settings	161
Configure CST Port Settings	162
View CST Port Status	164
View Rapid STP Information	166
Manage MST Settings	167
MST Port Configuration	169
View STP Statistics	172
Configure Multicast	173
View the MFDB Table	173
View the MFDB Statistics	174
Auto-Video	175
IGMP Snooping	176
Configure IGMP Snooping	176
Configure IGMP Snooping for Interfaces	178
View the IGMP Snooping Table	179
Configure IGMP Snooping for VLANs	180
Modify IGMP Snooping Settings for a VLAN	182
Disable IGMP Snooping on a VLAN and Remove It From the Table	182
Configure Multicast Router Interfaces	183
Configure a Multicast Router VLAN	184
IGMP Snooping Querier Overview	185
Configure IGMP Snooping Querier	185
Configure IGMP Snooping Querier for VLANs	186
Display IGMP Snooping Querier for VLAN Status	187
Enable MLD Snooping	189
Configure a MLD Snooping Interface	190
Configure MLD VLAN Settings	191
Enable or Disable a Multicast Router on Interfaces	193
Configure Multicast Router VLAN Settings	194
Configure MLD Snooping Querier	195
Configure MLD Snooping Querier VLAN Settings	196
Configure Multicast VLAN Registration	197
Configure Basic MVR Settings	198
Configure an MVR Group	199
Configure an MVR Interface	200
Configure MVR Group Membership	201
View MVR Statistics	202
View and Configure the MAC Address Table	203
Configure the MAC Address Table	204
Set the Dynamic Address Aging Interval	205
Configure a Static MAC Address	206
Configure Layer 2 Loop Protection	207
Configure Global Layer 2 Loop Protection	208
Configure Layer 2 Loop Protection on a Port	209
4. Configure Routing	211
Configure IP Settings	212
Configure the Router IP	212
IP Statistics	213
Configure IPv6	217
Configure IPv6 Global Settings	217
View the IPv6 Route Table	218
Configure IPv6 VLAN Interface Settings	219
IPv6 Prefix Configuration	222
View IPv6 Statistics	223
View the IPv6 Neighbor Table	228
IPv6 Static Route Configuration	230
View the IPv6 Route Table	231
IPv6 Route Preferences	232
Configure VLAN Routing	233
Use the VLAN Static Routing Wizard	233
VLAN Routing Configuration	235
Delete a VLAN Routing Interface	236
Configure Router Discovery	237
Manage Routes	238
Configure a Basic Route	238
Modify a Route	240
Delete a Route	241
Configure Address Resolution Protocol	242
Display Basic ARP Cache	242
Add an Entry to the ARP Table	244
View or Globally Configure the ARP Table	246
Remove an ARP Entry From the ARP Cache	247
5. Configure Quality of Service	249
Manage Class of Service	250
CoS Configuration	250
Configure Global CoS Settings	250
Configure CoS Interface Settings for an Interface	252
Configure CoS Queue Settings for an Interface	253
802.1p to Queue Mapping	255
DSCP to Queue Mapping	256
Manage Differentiated Services	257
Defining DiffServ	257
Configure DiffServ Settings	258
DiffServ Configuration	258
Configure a DiffServ Class	259
Configure DiffServ IPv6 Class Settings	265
Configure a DiffServ Policy	270
Configure the DiffServ Service Interface	276
View DiffServ Service Statistics	278
6. Manage Device Security	280
Management Security Settings	281
Change the Password	281
RADIUS Overview	282
Configure TACACS+	291
Authentication List Configuration	293
Manage the Smart Control Center Utility	297
Configure Management Access	298
Configure HTTP Settings	298
HTTPS Configuration	299
Manage Certificates	301
Download Certificates	303
Access Control	304
Configure Access Rule Settings	306
Configure Port Authentication	307
Configure Global 802.1X Settings	307
Manage Port Authentication	309
View the Port Summary	313
View the Client Summary	314
Set Up Traffic Control	315
Manage MAC Filtering	315
MAC Filter Summary	318
Storm Control	318
Port Security	320
Configure Protected Ports	324
Configure a Private VLAN	325
Configure Access Control Lists	331
Use the ACL Wizard to Create a Simple ACL	331
Configure a Basic MAC ACL	336
Configure MAC ACL Rules	339
Configure MAC Bindings	343
View or Delete MAC ACL Bindings in the MAC Binding Table	344
Configure an IP ACL	345
Configure Rules for a Basic IP ACL	347
Configure Rules for an Extended IP ACL	351
Configure IPv6 ACL	359
Configure IPv6 Rules	361
Configure IP ACL Interface Bindings	367
View or Delete IP ACL Bindings in the IP ACL Binding Table	369
Configure VLAN ACL Bindings	370
7. Monitor the System	372
Monitor the Switch and the Ports	373
Switch Statistics	373
View Port Statistics	376
View Detailed Port Statistics	378
View EAP Statistics	385
Perform a Cable Test	386
Configure and View Logs	388
Manage the Memory Logs	388
Message Log Format	390
Manage the Flash Log	390
Manage the Server Log	392
View the Trap Logs	395
View the Event Log	396
Format of the Messages	398
Configure Port Mirroring	398
8. Maintenance	401
Reboot the Switch	402
Reset the Switch to Its Factory Default Settings	402
Export a File From the Switch	403
Export a File to the TFTP Server	404
HTTP File Export	405
Export a File From the Switch to a USB Device	406
Download a File to the Switch	407
Download a File to the Switch Using TFTP	408
Download a File to the Switch Using HTTP	410
Download a File From a USB Device	412
Manage Files	413
Copy an Image	414
Configure Dual Image Settings	414
Dual Image Status	416
Troubleshooting	417
Ping IPv4	417
Ping IPv6	419
Traceroute IPv4	421
Traceroute IPv6	422
Remote Diagnostics	424
Configure Memory Dump Settings and Perform a Full Memory Dump	425
A. Configuration Examples	428
Virtual Local Area Networks (VLANs)	429
VLAN Configuration Examples	430
Access Control Lists (ACLs)	431
MAC ACL Sample Configuration	431
Standard IP ACL Sample Configuration	432
Differentiated Services (DiffServ)	433
Class	434
DiffServ Traffic Classes	435
Creating Policies	435
DiffServ Example Configuration	436
802.1X	438
802.1X Example Configuration	439
MSTP	440
MSTP Example Configuration	442
VLAN Routing Interface Configuration Example	444
B. Specifications and Default Settings	446
Switch Default Settings	447
General Feature Default Settings	448
System Setup and Maintenance Settings	455
Port Characteristics	455
Traffic Control Settings	456
Quality of Service Settings	456
Security Settings	457
System Management Settings	457

Match case Limit results 1 per page

Configure Routing

221

ProSAFE 8-Port or 16-Port Gigabit Smart Managed Switch Model GS418TPP, GS510TLP, and GS510TPP

14.

In the

Adv NS Interval

field, specify the retransmission time field of router advertisements

sent from the interface.

A value of 0 means the interval is not specified for the router. The range of the neighbor

solicit interval is 1000 to 4294967295. The default is 0.

15.

In the

Adv Reachable Interval

field, specify the router advertisement time.

This is the time allocated to consider the neighbors reachable after ND confirmation. The

range of reachable time is 0 to 3600000. The default is 0.

16.

In the

Adv Interval

field, specify the maximum time allowed between sending router

advertisements from the interface.

The range of the maximum advertisement interval is 4 to 1800. The default value is 600.

17.

From the

Adv Managed Config Flag

menu, specify the setting for the router advertisement

managed address configuration flag.

When the selection is

Enable

, end nodes use DHCPv6. When the selection is

Disable

end nodes autoconfigure addresses. The default value is Disable.

18.

From the

Adv Other Config Flag

menu, select to enable or disable the router

advertisement other stateful configuration flag.

The default value is Disable.

19.

From the

Router Preference

menu, specify the router preference advertisement on an

interface.

The default value is Medium.

20.

From the

Adv Suppress Flag

menu, select to enable or disable the router advertisement

suppression on an interface.

The default value is Disable.

21.

From the

Destination Unreachables

menu, select to enable or disable the mode for

sending ICMPv6 destination unreachable messages on this interface.

If this mode is disabled, the interface does not send ICMPv6 destination unreachable

messages. By default, the IPv6 destination unreachables mode is enabled.

22.

Click the

Apply

button.

The updated configuration is sent to the switch. Configuration changes take effect

immediately.

The following table describes the nonconfigurable data that is displayed.

Table 60.

IPv6 VLAN Configuration information

Field

Description

Routing Mode

The routing mode of an interface. The default is Disable.

Operational Mode

The operational state of an interface. The default value is Disable.

Link State

Indicates whether the link is up or down.