Dell Force10 S55T FTOS Command Line Reference Guide for the S55 System FTOS 8. - Page 476
show interfaces Command Example for 10G TeraScale, Table 15-6., Fields in show
View all Dell Force10 S55T manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 476 highlights
www.dell.com | support.dell.com Example Figure 15-28. show interfaces Command Example for 10G (TeraScale) Force10#show interfaces tengigabitethernet 0/0 TenGigabitEthernet 3/0 is up, line protocol is up Hardware is Force10Eth, address is 00:01:e8:41:77:c5 Current address is 00:01:e8:41:77:c5 Pluggable media present, XFP type is 10GBASE-SR Medium is MultiRate, Wavelength is 850.00nm XFP receive power reading is -2.4834 Interface index is 134545468 Port will not be disabled on partial SFM failure MTU 9252 bytes, IP MTU 9234 bytes LineSpeed 10000 Mbit Flowcontrol rx on tx on ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:15:14 Queueing strategy: fifo Input Statistics: 4410013700 packets, 282240876800 bytes 0 Vlans 4410013700 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 857732 packets, 54894848 bytes, 0 underruns 857732 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 24 Multicasts, 0 Broadcasts, 857708 Unicasts 0 Vlans,0 throttles, 0 discarded, 0 collisions, 4409143619 wredDrops Rate info (interval 30 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Time since last interface status change: 00:12:14 Force10# Table 15-6. Fields in show interfaces Command Example (TeraScale) Line TenGigabitEthernet 0/0... Hardware is... Pluggable media present... Interface index... Internet address... MTU 1554... LineSpeed ARP type:... Description Interface type, slot/port and administrative and line protocol status. Interface hardware information, assigned MAC address, and current address. Present pluggable media wavelength, type, and rate. The error scenarios are: • Wavelength, Non-qualified - Dell Force10 ID is not present, but wavelength information is available from XFP or SFP serial data • Wavelength, F10 unknown-Dell Force10 ID is present, but not able to determine the optics type • Unknown, Non-qualified- if wavelength is reading error, and F10 ID is not present Dell Force10 allows unsupported SFP and XFP transceivers to be used, but FTOS might not be able to retrieve some data about them. In that case, typically when the output of this field is "Pluggable media present, Media type is unknown", the Medium and the XFP/SFP receive power reading data might not be present in the output. Displays the interface index number used by SNMP to identify the interface. States whether an IP address is assigned to the interface. If one is, that address is displayed. Displays link and IP MTU information. Displays the interface's line speed, duplex mode, and Slave Displays the ARP type and the ARP timeout value for the interface. 476 | Interfaces