Home » Dell Manuals » Servers » Dell Force10 MXL Blade » Manual Viewer

Dell Force10 MXL Blade MXL 10/40GbE Switch IO Module FTOS Command Line Referen - Page 246

Bulk Configuration Warning Message, Interface Range prompt with Multiple Ports

View all Dell Force10 MXL Blade manuals

Add to My Manuals
Save this manual to your list of manuals

Page 246 highlights

www.dell.com | support.dell.com Parameters interface, interface,... Enter the keyword interface range and one of the interfaces - slot/port, port-channel or VLAN number. Select the range of interfaces for bulk configuration. You can enter up to six comma separated ranges-spaces are not required between the commas. Comma-separated ranges can include VLANs, port-channels and physical interfaces. Slot/Port information must contain a space before and after the dash. For example, interface range tengigabitethernet 0/1 - 5 is valid; interface range tengigabitethernet 0/1-5 is not valid. • For a Port Channel interface, enter the keyword port-channel followed by a number: Range: 1 to 128 • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet followed by the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE followed by the slot/port information. • For a VLAN, enter the keyword vlan followed by a number from 1 to 4094. Defaults none Command Modes CONFIGURATION Command History Usage Information Version 8.3.16.1 Introduced on MXL 10/40GbE Switch IO Module When creating an interface range, interfaces appear in the order they are entered; they are not sorted. The command verifies that interfaces are present (physical) or configured (logical). Important things to remember: • Bulk configuration is created if at least one interface is valid. • Non-existing interfaces are excluded from the bulk configuration with a warning message. • The interface range prompt includes interface types with slot/port information for valid interfaces. The prompt allows for a maximum of 32 characters. If the bulk configuration exceeds 32 characters, it is represented by an ellipsis When the interface range prompt has multiple port ranges, the smaller port range is excluded from the prompt. • If overlapping port ranges are specified, the port range is extended to the smallest start port and the biggest end port. Example Figure 14-11. Bulk Configuration Warning Message FTOS(conf)#interface range so 2/0 - 1 , te 10/0 , tengig 3/0 , fa 0/ 0 % Warning: Non-existing ports (not configured) are ignored by Example Figure 14-12. Interface Range prompt with Multiple Ports FTOS(conf)#interface range tengig 2/0 - 23 , tengig 2/1 - 10 FTOS(conf-if-range-tengig-2/0-23# 246 | Interfaces

Section	Page
About this Guide	9
Objectives	9
Audience	9
Conventions	9
Information Symbols	10
Related Documents	10
CLI Basics	11
Accessing the Command Line	11
Multiple Configuration Users	12
Navigating the Command Line Interface	12
Obtaining Help	13
Using the Keyword no	15
Filtering show Commands	15
Displaying All Output	16
Filtering Command Output Multiple Times	16
Command Modes	16
EXEC Mode	16
EXEC Privilege Mode	17
CONFIGURATION Mode	17
INTERFACE Mode	17
LINE Mode	18
MAC ACCESS LIST Mode	18
IP ACCESS LIST Mode	18
ROUTE-MAP Mode	18
PREFIX-LIST Mode	19
SPANNING TREE Mode	19
Per-VLAN SPANNING TREE Plus Mode	19
RAPID SPANNING TREE Mode	19
MULTIPLE SPANNING TREE Mode	20
PROTOCOL GVRP Mode	20
ROUTER OSPF Mode	20
ROUTER RIP Mode	20
File Management	21
Overview	21
Basic File Management Commands	21
Control and Monitoring	37
Commands	37
Important Points to Remember	67
u-Boot	81
Overview	81
Commands	81
Access Control Lists (ACL)	91
Overview	91
Commands Common to all ACL Types	91
Common IP ACL Commands	94
Standard IP ACL Commands	98
Extended IP ACL Commands	102
Common MAC Access List Commands	117
Standard MAC ACL Commands	120
Extended MAC ACL Commands	123
IP Prefix List Commands	127
Route Map Commands	132
Bare Metal Provisioning	143
Overview	143
Commands	143
Content Addressable Memory (CAM)	147
Overview	147
CAM Profile Commands	147
Important Points to Remember	147
Data Center Bridging	153
Overview	153
DCB Command	153
PFC Commands	153
ETS Commands	154
DCBX Commands	154
Dynamic Host Configuration Protocol (DHCP)	187
Overview	187
Commands to Configure the System to be a DHCP Server	187
Commands to Configure the System to be a DHCP Client	194
Other Commands supported by DHCP Client	195
Commands to Configure Secure DHCP	198
FIP Snooping	205
Overview	205
GARP VLAN Registration (GVRP)	217
Commands	217
Important Points to Remember	218
Internet Group Management Protocol (IGMP)	227
IGMP Snooping Commands	227
Important Points to Remember for IGMP Snooping	227
Important Points to Remember for IGMP Querier	228
Interfaces	235
Overview	235
Basic Interface Commands	235
Port Channel Commands	277
Time Domain Reflectometer (TDR)	284
Important Points to Remember	284
UDP Broadcast	286
Important Points to Remember	286
IPv4 Routing	289
Commands	289
iSCSI Optimization	323
Overview	323
Link Aggregation Control Protocol (LACP)	331
Overview	331
Commands	331
Layer 2	337
Overview	337
MAC Addressing Commands	337
Virtual LAN (VLAN) Commands	347
Link Layer Discovery Protocol (LLDP)	355
Overview	355
Commands	355
LLDP-MED Commands	363
Multiple Spanning Tree Protocol (MSTP)	371
Overview	371
Commands	371
Open Shortest Path First (OSPFv2)	385
Overview	385
OSPFv2 Commands	385
Port Monitoring	433
Overview	433
Commands	433
Important Points to Remember	433
Private VLAN (PVLAN)	439
Commands	439
Private VLAN Concepts	440
Per-VLAN Spanning Tree Plus (PVST+)	449
Overview	449
Commands	449
Quality of Service (QoS)	461
Overview	461
Global Configuration Commands	461
Per-Port QoS Commands	462
Policy-Based QoS Commands	467
Routing Information Protocol (RIP)	491
Overview	491
Commands	491
Remote Monitoring (RMON)	507
Overview	507
Commands	507
Rapid Spanning Tree Protocol (RSTP)	519
Overview	519
Commands	519
Security	531
Commands	531
AAA Accounting Commands	531
Authorization and Privilege Commands	534
Authentication and Password Commands	537
RADIUS Commands	548
TACACS+ Commands	552
SSH Server and SCP Commands	555
Secure DHCP Commands	566
sFlow	571
Overview	571
Important Points to Remember	571
Commands	572
Simple Network Management Protocol (SNMP) and Syslog	579
Overview	579
SNMP Commands	579
Important Points to Remember	580
Syslog Commands	594
Storm Control	605
Overview	605
Commands	605
Important Points to Remember	605
Stacking Commands	611
Overview	611
Commands	611
Spanning Tree Protocol (STP)	621
Overview	621
System Time and Date	631
Overview	631
Commands	631
Uplink Failure Detection (UFD)	645
Overview	645
Commands	645
VLAN Stacking	655
Overview	655
Important Points to Remember	655
Virtual Router Redundancy Protocol (VRRP)	663
IPv4 VRRP Commands	663
Debugging and Diagnostics	675
Offline Diagnostic Commands	675
Important Points to Remember	675
Buffer Tuning Commands	677
Hardware Commands	682
Internet Control Message Protocol (ICMP) Message Types	695
SNMP Traps	697
Index	701

Match case Limit results 1 per page

246

Interfaces

www.dell.com | support.dell.com

Parameters

Defaults

none

Command Modes

CONFIGURATION

Command

History

Usage

Information

When creating an interface range, interfaces appear in the order they are entered; they are not sorted.

The command verifies that interfaces are present (physical) or configured (logical). Important things to

remember:

•

Bulk configuration is created if at least one interface is valid.

•

Non-existing interfaces are excluded from the bulk configuration with a warning message.

•

The interface range prompt includes interface types with slot/port information for valid interfaces.

The prompt allows for a maximum of 32 characters. If the bulk configuration exceeds 32

characters, it is represented by an ellipsis ( ... ).

•

When the interface range prompt has multiple port ranges, the smaller port range is excluded from

the prompt.

•

If overlapping port ranges are specified, the port range is extended to the smallest start port and the

biggest end port.

Example

Figure 14-11.

Bulk Configuration Warning Message

Example

Figure 14-12.

Interface Range prompt with Multiple Ports

interface

Enter the keyword

interface range

and one of the interfaces — slot/port,

port-channel or VLAN number. Select the range of interfaces for bulk configuration.

You can enter up to six comma separated ranges—spaces are

not

required between the

commas. Comma-separated ranges can include VLANs, port-channels and physical

interfaces.

Slot/Port information must contain a space before and after the dash. For example,

interface range tengigabitethernet 0/1 - 5

is valid;

interface range

tengigabitethernet 0/1-5

is not valid.

•

For a Port Channel interface, enter the keyword

port-channel

followed by a

number:

Range: 1 to 128

•

For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

followed by the slot/port information.

•

For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

followed by the

slot/port information.

•

For a VLAN, enter the keyword

vlan

followed by a number from 1 to 4094.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

FTOS(conf)#interface range so 2/0 - 1 , te 10/0 , tengig 3/0

, fa 0/

% Warning: Non-existing ports (not configured) are ignored by

FTOS(conf)#interface range tengig 2/0 - 23 , tengig 2/1 - 10

FTOS(conf-if-range-tengig-2/0-23#