Home » Dell Manuals » Servers » Dell Force10 MXL Blade » Manual Viewer

Dell Force10 MXL Blade MXL 10/40GbE Switch IO Module FTOS Command Line Referen - Page 279

interface port-channel, group Command Example, interface port-channel Command Example

View all Dell Force10 MXL Blade manuals

Add to My Manuals
Save this manual to your list of manuals

Page 279 highlights

Command Modes Command History Example PORT-CHANNEL FAILOVER-GROUP (conf-po-failover-grp) Version 8.3.16.1 Introduced on MXL 10/40GbE Switch IO Module Figure 14-39. group Command Example FTOS(conf)#port-channel failover-group FTOS(conf-po-failover-grp)#group 1 port-channel 1 port-channel 2 FTOS(conf-po-failover-grp)# Related Commands port-channel failover-group show interfaces port-channel Accesses the PORT-CHANNEL FAILOVER-GROUP mode to configure a LAG failover group. Displays information on configured Port Channel groups. interface port-channel Create a Port Channel interface, which is a link aggregation group containing up to 16 physical interfaces on an MXL Switch. Syntax interface port-channel channel-number To delete a Port Channel, use the no interface port-channel channel-number command. Parameters channel-number For a Port Channel interface, enter the keyword port-channel followed by a number: Range: 1-128 Defaults Not configured. Command Modes CONFIGURATION Command History Version 8.3.16.1 Introduced on MXL 10/40GbE Switch IO Module Example Figure 14-40. interface port-channel Command Example FTOS(conf)#int port-channel 2 FTOS(conf-if-po-2)# Usage Information Port Channel interfaces are logical interfaces and can be either in Layer 2 mode (by configuring port-channel with switchport command) or Layer 3 mode (by configuring an IP address). You can add a Port Channel in Layer 2 mode to a VLAN. A Port Channel can contain both 100/1000 interfaces and GE interfaces. Based on the first interface configured in the Port Channel and enabled, FTOS determines if the Port Channel uses 100 Mb/s or 1000 Mb/s as the common speed. Refer to channel-member for more information. If the stack unit is in a Jumbo mode chassis, then the mtu and ip mtu commands can also be configured. The Link MTU and IP MTU values configured on the channel members must be greater than the Link MTU and IP MTU values configured on the Port Channel interface. Note: In a Jumbo-enabled system, all members of a Port Channel must be configured with the same link MTU values and the same IP MTU values. Interfaces | 279

Section	Page
About this Guide	9
Objectives	9
Audience	9
Conventions	9
Information Symbols	10
Related Documents	10
CLI Basics	11
Accessing the Command Line	11
Multiple Configuration Users	12
Navigating the Command Line Interface	12
Obtaining Help	13
Using the Keyword no	15
Filtering show Commands	15
Displaying All Output	16
Filtering Command Output Multiple Times	16
Command Modes	16
EXEC Mode	16
EXEC Privilege Mode	17
CONFIGURATION Mode	17
INTERFACE Mode	17
LINE Mode	18
MAC ACCESS LIST Mode	18
IP ACCESS LIST Mode	18
ROUTE-MAP Mode	18
PREFIX-LIST Mode	19
SPANNING TREE Mode	19
Per-VLAN SPANNING TREE Plus Mode	19
RAPID SPANNING TREE Mode	19
MULTIPLE SPANNING TREE Mode	20
PROTOCOL GVRP Mode	20
ROUTER OSPF Mode	20
ROUTER RIP Mode	20
File Management	21
Overview	21
Basic File Management Commands	21
Control and Monitoring	37
Commands	37
Important Points to Remember	67
u-Boot	81
Overview	81
Commands	81
Access Control Lists (ACL)	91
Overview	91
Commands Common to all ACL Types	91
Common IP ACL Commands	94
Standard IP ACL Commands	98
Extended IP ACL Commands	102
Common MAC Access List Commands	117
Standard MAC ACL Commands	120
Extended MAC ACL Commands	123
IP Prefix List Commands	127
Route Map Commands	132
Bare Metal Provisioning	143
Overview	143
Commands	143
Content Addressable Memory (CAM)	147
Overview	147
CAM Profile Commands	147
Important Points to Remember	147
Data Center Bridging	153
Overview	153
DCB Command	153
PFC Commands	153
ETS Commands	154
DCBX Commands	154
Dynamic Host Configuration Protocol (DHCP)	187
Overview	187
Commands to Configure the System to be a DHCP Server	187
Commands to Configure the System to be a DHCP Client	194
Other Commands supported by DHCP Client	195
Commands to Configure Secure DHCP	198
FIP Snooping	205
Overview	205
GARP VLAN Registration (GVRP)	217
Commands	217
Important Points to Remember	218
Internet Group Management Protocol (IGMP)	227
IGMP Snooping Commands	227
Important Points to Remember for IGMP Snooping	227
Important Points to Remember for IGMP Querier	228
Interfaces	235
Overview	235
Basic Interface Commands	235
Port Channel Commands	277
Time Domain Reflectometer (TDR)	284
Important Points to Remember	284
UDP Broadcast	286
Important Points to Remember	286
IPv4 Routing	289
Commands	289
iSCSI Optimization	323
Overview	323
Link Aggregation Control Protocol (LACP)	331
Overview	331
Commands	331
Layer 2	337
Overview	337
MAC Addressing Commands	337
Virtual LAN (VLAN) Commands	347
Link Layer Discovery Protocol (LLDP)	355
Overview	355
Commands	355
LLDP-MED Commands	363
Multiple Spanning Tree Protocol (MSTP)	371
Overview	371
Commands	371
Open Shortest Path First (OSPFv2)	385
Overview	385
OSPFv2 Commands	385
Port Monitoring	433
Overview	433
Commands	433
Important Points to Remember	433
Private VLAN (PVLAN)	439
Commands	439
Private VLAN Concepts	440
Per-VLAN Spanning Tree Plus (PVST+)	449
Overview	449
Commands	449
Quality of Service (QoS)	461
Overview	461
Global Configuration Commands	461
Per-Port QoS Commands	462
Policy-Based QoS Commands	467
Routing Information Protocol (RIP)	491
Overview	491
Commands	491
Remote Monitoring (RMON)	507
Overview	507
Commands	507
Rapid Spanning Tree Protocol (RSTP)	519
Overview	519
Commands	519
Security	531
Commands	531
AAA Accounting Commands	531
Authorization and Privilege Commands	534
Authentication and Password Commands	537
RADIUS Commands	548
TACACS+ Commands	552
SSH Server and SCP Commands	555
Secure DHCP Commands	566
sFlow	571
Overview	571
Important Points to Remember	571
Commands	572
Simple Network Management Protocol (SNMP) and Syslog	579
Overview	579
SNMP Commands	579
Important Points to Remember	580
Syslog Commands	594
Storm Control	605
Overview	605
Commands	605
Important Points to Remember	605
Stacking Commands	611
Overview	611
Commands	611
Spanning Tree Protocol (STP)	621
Overview	621
System Time and Date	631
Overview	631
Commands	631
Uplink Failure Detection (UFD)	645
Overview	645
Commands	645
VLAN Stacking	655
Overview	655
Important Points to Remember	655
Virtual Router Redundancy Protocol (VRRP)	663
IPv4 VRRP Commands	663
Debugging and Diagnostics	675
Offline Diagnostic Commands	675
Important Points to Remember	675
Buffer Tuning Commands	677
Hardware Commands	682
Internet Control Message Protocol (ICMP) Message Types	695
SNMP Traps	697
Index	701

Match case Limit results 1 per page

Interfaces

279

Command Modes

PORT-CHANNEL FAILOVER-GROUP (conf-po-failover-grp)

Command

History

Example

Figure 14-39.

group Command Example

Commands

interface port-channel

Create a Port Channel interface, which is a link aggregation group containing up to 16 physical

interfaces on an MXL Switch.

Syntax

interface port-channel

channel-number

To delete a Port Channel, use the

no interface port-channel

channel-number

command.

Parameters

Defaults

Not configured.

Command Modes

CONFIGURATION

Command

History

Example

Figure 14-40.

interface port-channel Command Example

Usage

Information

Port Channel interfaces are logical interfaces and can be either in Layer 2 mode (by configuring

port-channel with switchport command) or Layer 3 mode (by configuring an IP address). You can add

a Port Channel in Layer 2 mode to a VLAN.

A Port Channel can contain both 100/1000 interfaces and GE interfaces. Based on the first interface

configured in the Port Channel and enabled, FTOS determines if the Port Channel uses 100 Mb/s or

1000 Mb/s as the common speed. Refer to

channel-member

for more information.

If the stack unit is in a Jumbo mode chassis, then the

mtu

and ip mtu commands can also be configured.

The Link MTU and IP MTU values configured on the channel members must be greater than the Link

MTU and IP MTU values configured on the Port Channel interface.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

FTOS(conf)#port-channel failover-group

FTOS(conf-po-failover-grp)#group 1 port-channel 1 port-channel 2

FTOS(conf-po-failover-grp)#

port-channel failover-group

Accesses the PORT-CHANNEL FAILOVER-GROUP mode to configure

a LAG failover group.

show interfaces port-channel

Displays information on configured Port Channel groups.

channel-number

For a Port Channel interface, enter the keyword

port-channel

followed by a

number:

Range: 1-128

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

FTOS(conf)#int port-channel 2

FTOS(conf-if-po-2)#

Note:

In a Jumbo-enabled system, all members of a Port Channel must be configured with the

same link MTU values and the same IP MTU values.