Home » Netgear Manuals » Hubs & Switches » Netgear XCM8806 Chassis » Manual Viewer

Netgear XCM8806 Chassis Hardware Installation Guide - Page 1170

con igmp snooping forwarding-mode, source-group-vlan S, G.

View all Netgear XCM8806 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 1170 highlights

NETGEAR 8800 Chassis Switch CLI Manual Slow path flooding is done within the L2 VLAN only. Use the none option to effectively disable slow path flooding. You can use the show igmp command to see the configuration of slow path flooding. Example The following command configures the multicast data stream specified in access1 for slow path flooding: configure igmp snooping flood-list access1 The following command specifies that no policy file is to be used, this effectively disabling slow path flooding: configure igmp snooping flood-list none configure igmp snooping forwarding-mode configure igmp snooping forwarding-mode [group-vlan | source-group-vlan] Description Configures the format for stored multicast entries in hardware as either the default mode (S, G) or the optional mode (*, G). Syntax Description group-vlan source-group-vlan Stores multicast entries in the format (* , GroupIP, VlanId), which is also referred to as (*, G). Stores multicast entries in the format (SourceIP, GroupIP, VlanId), which is also referred to as (S, G). Default source-group-vlan (S, G). Usage Guidelines In networks where there are many sources for each multicast address, the default (S, G) format can consume storage space. To use less storage space for multicast entries, specify the (*, G) format with the group-vlan format. Note: Once the entries are programmed as (*, G), any multicast traffic for the group is forwarded based on the (*, G) entries and does not come to the CPU. Use the group-vlan option only with IGMPv2 networks. 1170 | Chapter 26. IP Multicast Commands

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345