Home » Netgear Manuals » Hubs & Switches » Netgear XCM8806 Chassis » Manual Viewer

Netgear XCM8806 Chassis Hardware Installation Guide - Page 125

show session, If you have two power supply controllers installed

View all Netgear XCM8806 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

NETGEAR 8800 Chassis Switch CLI Manual • Temperature-Specifies, in Celsius, the current temperature of the power supply controller. • Status-Specifies the status of the power supply controller. Example The following command displays the status of the installed power supply controllers: show power controller The following is sample output from this command: PSUCTRL-1 information: State: Operational PartInfo: PSUCTRL-1 04334-00021 450117-00-01 Revision: 1.0 FailureCode: 0 Odometer: 337 days 7 hours since Nov-30-2004 Temperature: 32.14 deg C Status: PSU CTRL Mode: Master PSUCTRL-2 information: State: Empty If you have two power supply controllers installed, the switch displays output about both of the power supply controllers: PSUCTRL-1 information: State: Operational PartInfo: PSUCTRL-1 04334-00021 450117-00-01 Revision: 1.0 FailureCode: 0 Odometer: 17 days 5 hours 30 minutes since Oct-19-2004 Temperature: 35.1 deg C Status: PSU CTRL Mode: Master PSUCTRL-2 information: State: Operational PartInfo: PSUCTRL-2 04334-00068 450117-00-01 Revision: 1.0 FailureCode: 0 Odometer: 4 days 13 hours since Sep-21-2004 Temperature: 33.56 deg C Status: PSU CTRL Mode: Backup show session show session {{detail} {}} {history} Chapter 3. Commands for Managing the Switch | 125

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345