Home » Netgear Manuals » Hubs & Switches » Netgear XCM8806 Chassis » Manual Viewer

Netgear XCM8806 Chassis Hardware Installation Guide - Page 1270

Defaults, Usage Guidelines, Example, Description, Syntax Description, con msdp peer sa-filter

View all Netgear XCM8806 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 1270 highlights

NETGEAR 8800 Chassis Switch CLI Manual tcpPassword vrname Specifies the password to use for MD5 authentication at the TCP level. The password must be an ASCII string with a maximum of 31 characters. Specifies the name of the virtual router to which this command applies. If a name is not specified, it is extracted from the current CLI context. Defaults By default, TCP MD5 authentication is disabled for the MSDP peer. Usage Guidelines NETGEAR recommends that you enable TCP MD5 authentication for all MSDP peers to protect MSDP sessions from attacks. You can execute this command only when the MSDP peer is disabled or when MSDP is globally disabled on that VR. Example The following command configures a password for the MSDP peer with the IP address 192.168.45.43, which automatically enables TCP MD5 authentication: configure msdp peer 192.168.45.43 password test123 The following command removes the password: configure msdp peer 192.168.45.43 password none configure msdp peer sa-filter configure msdp peer [ | all] sa-filter [in | out] [ | none] {vr } Description This command configures an incoming or outgoing policy filter for SA messages. Syntax Description filter-name in out peer all remoteaddr vrname Specifies the name of the policy associated with an SA filter. To remove an SA filter, enter the "none" CLI keyword for . Associates the SA filter with inbound SA messages. Associates the SA filter with outbound SA messages. Specifies all MSDP peers. Specifies the IP address of the MSDP peer. Specifies the name of the virtual router to which this command applies. If a name is not specified, it is extracted from the current CLI context. 1270 | Chapter 28. MSDP Commands

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345