Home » Netgear Manuals » Hubs & Switches » Netgear XCM8806 Chassis » Manual Viewer

Netgear XCM8806 Chassis Hardware Installation Guide - Page 1234

The following command displays the global PIM configuration and statistics

View all Netgear XCM8806 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 1234 highlights

NETGEAR 8800 Chassis Switch CLI Manual Default If no VLAN is specified, the configuration is displayed for all PIM interfaces. If no multicast group is specified for the rp-set option (Rendezvous Point set), all RPs are displayed. Usage Guidelines The detail version of this command displays the global statistics for PIM, as well as the details of each PIM enabled VLAN. Examples The following command displays the global PIM configuration and statistics: Switch. 14 # show pim PIM Enabled, Version 2 PIM CRP Disabled BSR state : ACCEPT_ANY ; BSR Hash Mask Length: 255.255.255.252 Current BSR Info : 0.0.0.0 (Priority 0) Configured BSR Info : 0.0.0.0 (Priority 0) CRP Adv Interval : 60 sec ; CRP Holdtime: 150 BSR Interval : 60 sec ; BSR Timeout : 130 Cache Timer : 210 sec ; Prune Timer : 210 Assert Timeout : 210 sec ; Register Suppression Timeout,Probe: 60, 5 Generation Id : 0x4a01a1a6 PIM-DM State Refresh Source Active Timer : 210 sec PIM-DM State Refresh TTL : 16 PIM-DM State Refresh Origination Interval: 60 sec Threshold for Last Hop Routers: 0 kbps Threshold for RP : 0 kbps Register-Rate-Limit-Interval : Always active PIM SSM address range : None Register Checksum to include data Active Sparse Ckts 0 Dense Ckts 2 Global Packet Statistics (In/Out) C-RP-Advs 0 0 Registers 0 0 RegisterStops 0 0 VLAN v36 vixia Cid IP Address 2 36.36.36.3 2 64.1.1.1 Designated Router /16 36.36.36.6 /16 64.1.1.1 Flags Hello J/P Int Int rifmd------R 30 60 rifmd------R 30 60 Nbrs 1 0 1234 | Chapter 26. IP Multicast Commands

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345