Home » Netgear Manuals » Hubs & Switches » Netgear XCM8806 Chassis » Manual Viewer

Netgear XCM8806 Chassis Hardware Installation Guide - Page 28

Examples, Description, Syntax Description, Default, Usage Guidelines, con failsafe-account

View all Netgear XCM8806 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

NETGEAR 8800 Chassis Switch CLI Manual The default value for the virtual router used by the DNS client option is VR-Default. Examples The following command deletes a domain name from the domain suffix list: configure dns-client delete domain-suffix xyz_inc.com The following command removes a DNS server from the list: configure dns-client delete name-server 10.1.2.1 configure failsafe-account configure failsafe-account {[deny | permit] [all | control | serial | ssh  {vr } | telnet {vr }]} Description Configures a name and password for the failsafe account, or restricts access to specified connection types. Syntax Description deny permit all control serial ssh telnet Prohibits failsafe account usage over the specified connection type(s). Allows a failsafe account to be used over the specified connection type(s). Specifies all connection types. Specifies internal access between nodes in a NETGEAR 8800 or between MSMs/MMs in a chassis. Specifies access over the switch console port. Specifies access using SSH on specified or all virtual routers. Specifies access using Telnet on specified or all virtual routers. Default The failsafe account is always configured. The default connection types over which failsafe account access is permitted are the same as if "permit all" is configured. Usage Guidelines The failsafe account is the account of last resort to access your switch. If you use the command with no parameters, you are prompted for the failsafe account name and prompted twice to specify the password for the account. The password does not appear on the display at any time. You are not required to know the current failsafe account and password in order to change it. 28 | Chapter 2. Commands for Accessing the Switch

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345