Home » Netgear Manuals » Hubs & Switches » Netgear XCM8806 Chassis » Manual Viewer

Netgear XCM8806 Chassis Hardware Installation Guide - Page 86

con snmpv3 delete group user

View all Netgear XCM8806 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

NETGEAR 8800 Chassis Switch CLI Manual param_name Specifies to delete the filter profile with the specified profile name and parameter name in ASCII format. Default The default storage type is non-volatile. Usage Guidelines Use this command to delete entries from the snmpNotifyFilterProfileTable. This table associates a filter profile with a parameter name. Specify all to remove all entries. Specify a profile name to delete all entries for that profile name. Specify a profile name and a parameter name to delete just those entries for that filter profile and parameter name. Example The following command deletes the filter profile prof1 with the parameter name P1: configure snmpv3 delete filter-profile prof1 param P1 configure snmpv3 delete group user configure snmpv3 delete group {[[hex ] | ]} user [all-non-defaults | {[[hex ] | ] {sec-model [snmpv1|snmpv2c|usm]}}] Description Deletes a user name (security name) from a group. Syntax Description hex_group_name group_name all-non-defaults hex_user_name user_name sec-model snmpv1 snmpv2c usm Specifies the group name to delete or modify. The value is to be supplied as a colon separated string of hex octets. Specifies the group name to delete or modify in ASCII format. Specifies that all non-default (non-permanent) users are to be deleted from the group. Specifies the user name to delete or modify. The value is to be supplied as a colon separated string of hex octets. Specifies the user name to delete or modify in ASCII format. Specifies the security model to use. Specifies the SNMPv1 security model. Specifies the SNMPv2c security model. Specifies the SNMPv3 User-based Security Model (USM). 86 | Chapter 3. Commands for Managing the Switch

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345