Home » Netgear Manuals » Hubs & Switches » Netgear XCM8806 Chassis » Manual Viewer

Netgear XCM8806 Chassis Hardware Installation Guide - Page 794

Example, Description, Syntax Description, Usage Guidelines, con vrrp vlan vrid add ipaddress

View all Netgear XCM8806 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 794 highlights

NETGEAR 8800 Chassis Switch CLI Manual Example The following command clears the VRRP statistics on VRRP VLAN v1: clear counters vrrp vlan v1 The following command clears the VRRP statistics for VRID 1 on VRRP VLAN v1: clear counters vrrp vlan v1 vrid 1 configure vrrp vlan vrid add ipaddress configure vrrp vlan vrid add Description Associates a virtual IP address with a specific VRRP virtual router. Syntax Description vlan_name vridval ipaddress Specifies the name of a VRRP VLAN. Specifies a VRRP Virtual Router ID (VRID). Value can be in the range of 1-255. Specifies the IP address of the virtual router in which this device participates. Usage Guidelines The restrictions on this command are as follows: • If the priority of the VRRP virtual router is 255, the IP address to be added must be owned by the VLAN on which the VRRP virtual router exists. If the priority is not 255, the IP address must not be owned by that VLAN. • When a VRRP virtual router is enabled, it must have at least one virtual IP address. Example Create a VLAN named vlan-1 with an ipaddress of 10.1.2.2 and a VRRP VRID of 1: create vlan vlan-1 configure vlan vlan-1 ipaddress 10.1.2.2 create vrrp vlan-1 vrid 1 The following example associates IP address 10.1.2.3 to VLAN vlan-1: configure vrrp vlan vlan-1 vrid 1 add 10.1.2.3 configure vrrp vlan vrid add track-iproute configure vrrp vlan vrid add track-iproute  / 794 | Chapter 18. VRRP Commands

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345