Home » Netgear Manuals » Hubs & Switches » Netgear XCM8806 Chassis » Manual Viewer

Netgear XCM8806 Chassis Hardware Installation Guide - Page 1214

Table 28, Example, Description, Syntax Description, mtrace

View all Netgear XCM8806 Chassis manuals

Add to My Manuals
Save this manual to your list of manuals

Page 1214 highlights

NETGEAR 8800 Chassis Switch CLI Manual This information is described in Table 28. Table 28. mrinfo Command Display Data Data Metric Threshold Type querier leaf down Description This should always be 1 because mrinfo queries the directly connected interfaces of a device. This should always be 0 because the threshold feature is not supported. The type specifies the multicast protocol type. Because the NETGEAR 8800 only supports PIM, this value is always pim. The querier flag indicates that the queried router is the IGMP querier. The leaf flag indicates that the IP interface has no neighbor router. The down flag indicates that the interface link status is down. Example The following command requests information from multicast router 1.1.1.1: Switch.1 # mrinfo 1.1.1.1 1.1.1.1 [Flags:PGM] 2.2.2.1 -> 2.2.2.2 [1/0/pim/querier] 1.1.1.1 -> 0.0.0.0 [1/0/pim/querier/leaf] 8.8.8.1 -> 8.8.8.4 [1/0/pim/querier] 3.3.3.1 -> 0.0.0.0 [1/0/pim/down] mtrace mtrace source {destination } {group } {from } {gateway } {timeout } {maximum-hops } {vr } Description Traces multicast traffic from the receiver back to the source. Syntax Description src_address dest_address grp_address from_address Specifies the unicast IP address of the multicast source. Specifies the unicast IP address of the multicast group receiver. Specifies the multicast IP address of the group. Specifies the unicast IP address of the interface where the mtrace request originates. This is used as the IP destination address of the mtrace response packet. 1214 | Chapter 26. IP Multicast Commands

Section	Page
NETGEAR 8800 Chassis Switch CLI Manual	1
Contents	3
1. Command Reference Overview	6
Introduction	6
Audience	6
Structure of this Guide	7
Understanding the Command Syntax	7
Access Levels	7
Syntax Symbols	8
Syntax Helper	8
Object Names	9
Command Shortcuts	10
Port Numbering	10
Numerical Ranges	10
Line-Editing Keys	11
Command History	12
2. Commands for Accessing the Switch	13
3. Commands for Managing the Switch	57
SNMP	57
Telnet	58
TFTP	58
System Redundancy with Dual Management Modules Installed	58
Power Supply Management	58
Simple Network Time Protocol	59
4. Commands for Managing the NETGEAR 8800 Software	157
5. Commands for Configuring Slots and Ports on a Switch	190
6. Commands for Configuring LLDP	269
7. PoE Commands	300
Summary of PoE Software Features	300
8. Commands for Status Monitoring and Statistics	330
Event Management System	330
sFlow Statistics	331
RMON	331
9. VLAN Commands	425
10. FDB Commands	453
11. Commands for Virtual Routers	472
12. Policy Manager Commands	481
13. ACL Commands	487
14. QoS Commands	520
15. Security Commands	554
SSH	554
SSL	554
User Authentication	554
Denial of Service	555
16. Network Login Commands	679
17. STP Commands	737
STP	737
RSTP	737
MSTP	738
Spanning Tree Domains	738
Member VLANs	738
Carrier VLAN	738
Protected VLAN	739
STPD Modes	739
Encapsulation Modes	740
STP Rules and Restrictions	741
18. VRRP Commands	793
19. IP Unicast Commands	814
20. IPv6 Unicast Commands	904
21. RIP Commands	950
22. RIPng Commands	973
23. OSPF Commands	994
OSPF Edge Mode	995
24. OSPFv3 Commands	1036
OSPF Edge Mode	1037
25. BGP Commands	1075
26. IP Multicast Commands	1163
27. IPv6 Multicast Commands	1242
28. MSDP Commands	1261
29. vMAN (PBN) Commands	1296
A. Configuration and Image Commands	1306
B. Troubleshooting Commands	1345
Event Management System	1345