Home » Dell Manuals » Servers » Dell S6000 » Manual Viewer

Dell S6000 FTOS 9.0(2.0) Command Line Reference Guide for the System - Page 460

group

Add to My Manuals
Save this manual to your list of manuals

Page 460 highlights

www.dell.com | support.dell.com • The Port Channel link MTU and IP MTU must be less than or equal to the link MTU and IP MTU values configured on the channel members. Example: If the members have a link MTU of 2100 and an IP MTU 2000, the Port Channel's MTU values cannot be higher than 2100 for link MTU or 2000 bytes for IP MTU. When an interface is removed from a Port Channel with the no channel-member command syntax, the interface reverts to its configuration prior to joining the Port Channel. An interface can belong to only one Port Channel. If the Port Channel contains a mix of interfaces with 100 Mb/s speed and 1000 Mb/s speed, the software disables those interfaces whose speed does not match the speed of the first interface configured and enabled in the Port Channel. If that first interface goes down, the Port Channel does not change its designated speed; you must disable and re-enable the Port Channel or change the order of the channel members configuration to change the designated speed. Refer to the FTOS Configuration Guide for more information on Port Channels. Related Commands description interface port-channel shutdown Assign a descriptive text string to the interface. Create a Port Channel interface. Disable/Enable the port channel. group s z S6000 Group two LAGs in a supergroup ("fate-sharing group" or "failover group"). Syntax group group_number port-channel number port-channel number To remove an existing LAG supergroup, use the no group group_number command. Parameters group_number port-channel number Enter an integer from 1 to 32 that will uniquely identify this LAG fate-sharing group. Enter the keyword port-channel followed by an existing LAG number. Enter this keyword/variable combination twice, identifying the two LAGs to be paired. Defaults No default values or behavior Command Modes PORT-CHANNEL FAILOVER-GROUP (conf-po-failover-grp) Command History Version 9.0.2.0 Version 8.3.11.1 Version 8.3.7.0 Introduced on the S6000. Introduced on Z9000 Introduced on the S4810. Example Related Commands FTOS(conf)#port-channel failover-group FTOS(conf-po-failover-grp)#group 1 port-channel 1 port-channel 2 FTOS(conf-po-failover-grp)# port-channel failover-group show interfaces port-channel Access the PORT-CHANNEL FAILOVER-GROUP mode to configure a LAG failover group. Display information on configured Port Channel groups. 460 | Interfaces

Section	Page
About this Guide	11
Objectives	11
Audience	11
Conventions	11
Information Symbols	12
Related Documents	12
CLI Basics	13
Accessing the Command Line	13
Multiple Configuration Users	14
Navigating the Command Line Interface	14
Obtaining Help	15
Using the Keyword No	17
Filtering show Commands	17
Displaying All Output	18
Filtering Command Output Multiple Times	18
Command Modes	18
EXEC Mode	19
EXEC Privilege Mode	19
CONFIGURATION Mode	19
INTERFACE Mode	19
LINE Mode	20
TRACE-LIST Mode	20
MAC ACCESS LIST Mode	20
IP ACCESS LIST Mode	21
ROUTE-MAP Mode	21
PREFIX-LIST Mode	21
AS-PATH ACL Mode	21
IP COMMUNITY LIST Mode	22
REDIRECT-LIST Mode	22
SPANNING TREE Mode	22
Per-VLAN SPANNING TREE Plus Mode	22
RAPID SPANNING TREE Mode	23
MULTIPLE SPANNING TREE Mode	23
PROTOCOL GVRP Mode	23
ROUTER OSPF Mode	23
ROUTER RIP Mode	24
ROUTER BGP Mode	24
Determining the Chassis Mode	24
File Management	25
Overview	25
Basic File Management Commands	25
Control and Monitoring	43
Overview	43
Commands	43
802.1X	95
Important Points to Remember	96
Access Control Lists (ACL)	111
Overview	111
Commands Common to all ACL Types	111
Common IP ACL Commands	113
Standard IP ACL Commands	117
Extended IP ACL Commands	123
Common MAC Access List Commands	139
Standard MAC ACL Commands	142
Extended MAC ACL Commands	145
IP Prefix List Commands	150
IPv6 ACL Commands	155
Route Map Commands	176
Boot Command Line Interface (BCLI)	195
Overview	195
Commands	195
Bidirectional Forwarding Detection (BFD)	205
Overview	205
Commands	205
Border Gateway Protocol	209
Overview	209
BGP IPv4 Commands	210
MBGP Commands	287
BGP Extended Communities (RFC 4360)	289
IPv6 BGP Commands	298
IPv6 MBGP Commands	299
Bare Metal Provisioning	301
Overview	301
Commands	301
Content Addressable Memory (CAM)	305
Overview	305
CAM Profile Commands	305
Important Points to Remember	305
Control Plane Policing (CoPP)	311
Overview	311
Commands	311
Data Center Bridging (DCB)	317
Overview	317
DCB Command	317
PFC Commands	317
ETS Commands	317
DCBX Commands	318
Debugging and Diagnostics	341
Overview	341
Diagnostics and Monitoring Commands	341
Offline Diagnostic Commands	344
Important Points to Remember	344
Hardware Commands	347
Dynamic Host Configuration Protocol (DHCP)	357
Overview	357
Commands to Configure the System to be a DHCP Server	357
Commands to Configure Secure DHCP	365
Equal Cost Multi-Path	373
Overview	373
Commands	373
Force10 Resilient Ring Protocol (FRRP)	381
Overview	381
Commands	381
Important Points to Remember	381
GARP VLAN Registration (GVRP)	389
Overview	389
Commands	389
Important Points to Remember	390
Internet Group Management Protocol (IGMP)	399
Overview	399
IGMP Commands	399
Important Points to Remember	399
IGMP Snooping Commands	409
Important Points to Remember for IGMP Snooping	409
Important Points to Remember for IGMP Querier	409
Interfaces	415
Overview	415
Basic Interface Commands	415
Port Channel Commands	458
IPv4 Routing	467
Overview	467
Commands	467
Link Aggregation Control Protocol (LACP)	509
Overview	509
Commands	509
Intermediate System to Intermediate System (IS-IS)	515
Overview	515
Commands	515
Layer 2	561
Overview	561
MAC Addressing Commands	561
Virtual LAN (VLAN) Commands	572
Far-End Failure Detection (FEFD)	580
Commands	580
Link Layer Detection Protocol (LLDP)	585
Overview	585
Commands	585
LLDP-MED Commands	594
Multicast Source Discovery Protocol (MSDP)	603
Overview	603
Commands	603
Multiple Spanning Tree Protocol (MSTP)	615
Overview	615
Commands	615
Multicast	629
Overview	629
IPv4 Multicast Commands	629
Open Shortest Path First (OSPFv2)	635
Overview	635
OSPFv2 Commands	635
PIM-Sparse Mode (PIM-SM)	689
Overview	689
IPv4 PIM-Sparse Mode Commands	689
PIM-Source Specific Mode (PIM-SSM)	703
Overview	703
IPv4 PIM-Source Specific Mode Commands	703
Port Monitoring	705
Overview	705
Commands	705
Important Points to Remember	705
Private VLAN (PVLAN)	711
Overview	711
Commands	711
Private VLAN Concepts	711
Per-VLAN Spanning Tree Plus (PVST+)	721
Overview	721
Commands	721
Quality of Service (QoS)	733
Overview	733
Global Configuration Commands	733
Per-Port QoS Commands	736
Policy-Based QoS Commands	740
Router Information Protocol (RIP)	767
Overview	767
Commands	767
Remote Monitoring (RMON)	785
Overview	785
Commands	785
Rapid Spanning Tree Protocol (RSTP)	797
Overview	797
Commands	797
Security	807
Overview	807
Commands	807
AAA Accounting Commands	807
Authorization and Privilege Commands	810
Authentication and Password Commands	814
RADIUS Commands	825
TACACS+ Commands	830
Port Authentication (802.1X) Commands	833
Important Points to Remember	834
SSH Server and SCP Commands	842
Secure DHCP Commands	854
Service Provider Bridging	859
Overview	859
Commands	859
Important Points to Remember	859
sFlow	865
Overview	865
Important Points to Remember	865
Commands	866
Simple Network Management Protocol and Syslog	873
Overview	873
SNMP Commands	873
Important Points to Remember	874
Syslog Commands	889
Storm Control	903
Overview	903
Commands	903
Important Points to Remember	903
Spanning Tree Protocol (STP)	911
Overview	911
Commands	911
System Time and Date	921
Overview	921
Commands	921
VLAN Stacking	937
Overview	937
Commands	937
Important Points to Remember	937
Virtual Router Redundancy Protocol (VRRP)	947
Overview	947
Commands	947
ICMP Message Types	961

Match case Limit results 1 per page

460

Interfaces

www.dell.com | support.dell.com

•

The Port Channel link MTU and IP MTU must be less than or equal to the link MTU and IP MTU

values configured on the channel members.

Example: If the members have a link MTU of 2100 and an IP MTU 2000, the Port Channel’s MTU

values cannot be higher than 2100 for link MTU or 2000 bytes for IP MTU.

When an interface is removed from a Port Channel with the

no channel-member

command syntax, the

interface reverts to its configuration prior to joining the Port Channel.

An interface can belong to only one Port Channel.

If the Port Channel contains a mix of interfaces with 100 Mb/s speed and 1000 Mb/s speed, the

software disables those interfaces whose speed does not match the speed of the first interface

configured and enabled in the Port Channel. If that first interface goes down, the Port Channel does not

change its designated speed; you must disable and re-enable the Port Channel or change the order of

the channel members configuration to change the designated speed. Refer to the

FTOS Configuration

Guide

for more information on Port Channels.

Commands

group

s z

Group two LAGs in a supergroup (“fate-sharing group” or “failover group”).

Syntax

group

group_number

port-channel

number

port-channel

number

To remove an existing LAG supergroup, use the

no group

group_number

command.

Parameters

Defaults

No default values or behavior

Command Modes

PORT-CHANNEL FAILOVER-GROUP (conf-po-failover-grp)

Command History

Example

FTOS(conf)#port-channel failover-group

FTOS(conf-po-failover-grp)#group 1 port-channel 1 port-channel 2

FTOS(conf-po-failover-grp)#

Commands

description

Assign a descriptive text string to the interface.

interface port-channel

Create a Port Channel interface.

shutdown

Disable/Enable the port channel.

S6000

group_number

Enter an integer from 1 to 32 that will uniquely identify this LAG

fate-sharing group.

port-channel

number

Enter the keyword

port-channel

followed by an existing LAG

number

Enter this keyword/variable combination twice, identifying the two LAGs to

be paired.

Version 9.0.2.0

Introduced on the S6000.

Version 8.3.11.1

Introduced on Z9000

Version

8.3.7.0

Introduced on the S4810.

port-channel failover-group

Access the PORT-CHANNEL FAILOVER-GROUP mode to configure a

LAG failover group.

show interfaces port-channel

Display information on configured Port Channel groups.