Home » Dell Manuals » Servers » Dell S6000 » Manual Viewer

Dell S6000 FTOS 9.0(2.0) Command Line Reference Guide for the System - Page 547

redistribute bgp

Add to My Manuals
Save this manual to your list of manuals

Page 547 highlights

Command History Version 9.0.2.0 Version 8.3.7.0 Introduced on the S6000. Introduced on the S4810. Usage Information To redistribute a default route (0.0.0.0/0), configure the default-information originate command. Changing or disabling a keyword in this command will not affect the state of the other command keywords. When an LSP with an internal metric is received, the FTOS considers the route cost taking into consideration the advertised cost to reach the destination. Redistributed routing information is filtered with the distribute-list out command to ensure that the routes are properly are passed to the receiving routing protocol. How a metric value assigned to a redistributed route is advertised depends on how on the configuration of the metric-style command. If the metric-style command is set for narrow or transition mode and the metric value in the redistribute command is set to a number higher than 63, the metric value advertised in LSPs will be 63. If the metric-style command is set for wide mode, an the metric value in the redistribute command is advertised. Related Commands default-information originate distribute-list out Generate a default route for the IS-IS domain. Suppress networks from being advertised in updates. Redistributed routing information is filtered by this command. redistribute bgp S6000 Redistribute routing information from a BGP process. (new command in Release 6.3.1) Syntax redistribute bgp AS number [level-1| level-1-2 | level-2] [metric metric-value] [metric-type {external| internal} ] [route-map map-name] To return to the default values, enter the no redistribute bgp command with the appropriate parameters. Parameters AS number level-1 level-1-2 level-2 metric metric-value Enter a number that corresponds to the Autonomous System number. Range: 1 to 65355 (OPTIONAL) Routes are independently redistributed into IS-IS Level 1 routes only (OPTIONAL) Routes are independently redistributed into IS-IS Level 1 and Level 2 routes. (OPTIONAL) Routes are independently redistributed into IS-IS as Level 2 routes only. This is the default. (OPTIONAL) The value used for the redistributed route. You should use a metric value that is consistent with the destination protocol. Range: 0 to 16777215 Default: 0. | 547

Section	Page
About this Guide	11
Objectives	11
Audience	11
Conventions	11
Information Symbols	12
Related Documents	12
CLI Basics	13
Accessing the Command Line	13
Multiple Configuration Users	14
Navigating the Command Line Interface	14
Obtaining Help	15
Using the Keyword No	17
Filtering show Commands	17
Displaying All Output	18
Filtering Command Output Multiple Times	18
Command Modes	18
EXEC Mode	19
EXEC Privilege Mode	19
CONFIGURATION Mode	19
INTERFACE Mode	19
LINE Mode	20
TRACE-LIST Mode	20
MAC ACCESS LIST Mode	20
IP ACCESS LIST Mode	21
ROUTE-MAP Mode	21
PREFIX-LIST Mode	21
AS-PATH ACL Mode	21
IP COMMUNITY LIST Mode	22
REDIRECT-LIST Mode	22
SPANNING TREE Mode	22
Per-VLAN SPANNING TREE Plus Mode	22
RAPID SPANNING TREE Mode	23
MULTIPLE SPANNING TREE Mode	23
PROTOCOL GVRP Mode	23
ROUTER OSPF Mode	23
ROUTER RIP Mode	24
ROUTER BGP Mode	24
Determining the Chassis Mode	24
File Management	25
Overview	25
Basic File Management Commands	25
Control and Monitoring	43
Overview	43
Commands	43
802.1X	95
Important Points to Remember	96
Access Control Lists (ACL)	111
Overview	111
Commands Common to all ACL Types	111
Common IP ACL Commands	113
Standard IP ACL Commands	117
Extended IP ACL Commands	123
Common MAC Access List Commands	139
Standard MAC ACL Commands	142
Extended MAC ACL Commands	145
IP Prefix List Commands	150
IPv6 ACL Commands	155
Route Map Commands	176
Boot Command Line Interface (BCLI)	195
Overview	195
Commands	195
Bidirectional Forwarding Detection (BFD)	205
Overview	205
Commands	205
Border Gateway Protocol	209
Overview	209
BGP IPv4 Commands	210
MBGP Commands	287
BGP Extended Communities (RFC 4360)	289
IPv6 BGP Commands	298
IPv6 MBGP Commands	299
Bare Metal Provisioning	301
Overview	301
Commands	301
Content Addressable Memory (CAM)	305
Overview	305
CAM Profile Commands	305
Important Points to Remember	305
Control Plane Policing (CoPP)	311
Overview	311
Commands	311
Data Center Bridging (DCB)	317
Overview	317
DCB Command	317
PFC Commands	317
ETS Commands	317
DCBX Commands	318
Debugging and Diagnostics	341
Overview	341
Diagnostics and Monitoring Commands	341
Offline Diagnostic Commands	344
Important Points to Remember	344
Hardware Commands	347
Dynamic Host Configuration Protocol (DHCP)	357
Overview	357
Commands to Configure the System to be a DHCP Server	357
Commands to Configure Secure DHCP	365
Equal Cost Multi-Path	373
Overview	373
Commands	373
Force10 Resilient Ring Protocol (FRRP)	381
Overview	381
Commands	381
Important Points to Remember	381
GARP VLAN Registration (GVRP)	389
Overview	389
Commands	389
Important Points to Remember	390
Internet Group Management Protocol (IGMP)	399
Overview	399
IGMP Commands	399
Important Points to Remember	399
IGMP Snooping Commands	409
Important Points to Remember for IGMP Snooping	409
Important Points to Remember for IGMP Querier	409
Interfaces	415
Overview	415
Basic Interface Commands	415
Port Channel Commands	458
IPv4 Routing	467
Overview	467
Commands	467
Link Aggregation Control Protocol (LACP)	509
Overview	509
Commands	509
Intermediate System to Intermediate System (IS-IS)	515
Overview	515
Commands	515
Layer 2	561
Overview	561
MAC Addressing Commands	561
Virtual LAN (VLAN) Commands	572
Far-End Failure Detection (FEFD)	580
Commands	580
Link Layer Detection Protocol (LLDP)	585
Overview	585
Commands	585
LLDP-MED Commands	594
Multicast Source Discovery Protocol (MSDP)	603
Overview	603
Commands	603
Multiple Spanning Tree Protocol (MSTP)	615
Overview	615
Commands	615
Multicast	629
Overview	629
IPv4 Multicast Commands	629
Open Shortest Path First (OSPFv2)	635
Overview	635
OSPFv2 Commands	635
PIM-Sparse Mode (PIM-SM)	689
Overview	689
IPv4 PIM-Sparse Mode Commands	689
PIM-Source Specific Mode (PIM-SSM)	703
Overview	703
IPv4 PIM-Source Specific Mode Commands	703
Port Monitoring	705
Overview	705
Commands	705
Important Points to Remember	705
Private VLAN (PVLAN)	711
Overview	711
Commands	711
Private VLAN Concepts	711
Per-VLAN Spanning Tree Plus (PVST+)	721
Overview	721
Commands	721
Quality of Service (QoS)	733
Overview	733
Global Configuration Commands	733
Per-Port QoS Commands	736
Policy-Based QoS Commands	740
Router Information Protocol (RIP)	767
Overview	767
Commands	767
Remote Monitoring (RMON)	785
Overview	785
Commands	785
Rapid Spanning Tree Protocol (RSTP)	797
Overview	797
Commands	797
Security	807
Overview	807
Commands	807
AAA Accounting Commands	807
Authorization and Privilege Commands	810
Authentication and Password Commands	814
RADIUS Commands	825
TACACS+ Commands	830
Port Authentication (802.1X) Commands	833
Important Points to Remember	834
SSH Server and SCP Commands	842
Secure DHCP Commands	854
Service Provider Bridging	859
Overview	859
Commands	859
Important Points to Remember	859
sFlow	865
Overview	865
Important Points to Remember	865
Commands	866
Simple Network Management Protocol and Syslog	873
Overview	873
SNMP Commands	873
Important Points to Remember	874
Syslog Commands	889
Storm Control	903
Overview	903
Commands	903
Important Points to Remember	903
Spanning Tree Protocol (STP)	911
Overview	911
Commands	911
System Time and Date	921
Overview	921
Commands	921
VLAN Stacking	937
Overview	937
Commands	937
Important Points to Remember	937
Virtual Router Redundancy Protocol (VRRP)	947
Overview	947
Commands	947
ICMP Message Types	961

Match case Limit results 1 per page

547

Command

History

Usage

Information

To redistribute a default route (0.0.0.0/0), configure the

default-information originate

command.

Changing or disabling a keyword in this command will not affect the state of the other command

keywords.

When an LSP with an internal metric is received, the FTOS considers the route cost taking into

consideration the advertised cost to reach the destination.

Redistributed routing information is filtered with the

distribute-list out

command to ensure that the

routes are properly are passed to the receiving routing protocol.

How a metric value assigned to a redistributed route is advertised depends on how on the configuration

of the

metric-style

command. If the

metric-style

command is set for narrow or transition mode and the

metric value in the

redistribute

command is set to a number higher than 63, the metric value advertised

in LSPs will be 63. If the

metric-style

command is set for wide mode, an the metric value in the

redistribute

command is advertised.

Commands

redistribute bgp

Redistribute routing

information from a BGP process. (new command in Release 6.3.1)

Syntax

redistribute bgp

AS number

[

level-1

level-1-2

level-2

] [

metric

metric-value

] [

metric-type

{external

internal

}

] [

route-map

map-name

]

To return to the default values, enter the

no redistribute bgp

command with the appropriate

parameters.

Parameters

Version 9.0.2.0

Introduced on the S6000.

Version

8.3.7.0

Introduced on the S4810.

default-information originate

Generate a default route for the IS-IS domain.

distribute-list out

Suppress networks from being advertised in updates. Redistributed

routing information is filtered by this command.

S6000

AS number

Enter a number that corresponds to the Autonomous System number.

Range: 1 to 65355

level-1

(OPTIONAL) Routes are independently redistributed into IS-IS Level 1

routes only

level-1-2

(OPTIONAL) Routes are independently redistributed into IS-IS Level 1 and

Level 2 routes.

level-2

(OPTIONAL) Routes are independently redistributed into IS-IS as Level 2

routes only.

This is the default.

metric

metric-value

(OPTIONAL) The value used for the redistributed route. You should use a

metric value that is consistent with the destination protocol.

Range: 0 to 16777215

Default: 0.