Sony XVS-7000 Users Guide - Page 112

- Key delegation buttons in the memory recall section on the Flexi Pad control block (key operation mode) • You can assign a key source bus delegation button to the 1st row or 2nd row of the AUX bus control block (AUX bus operation mode) in the Setup menu (see page 417). To select a video signal assigned to a cross-point button Set the operation mode that allows you to select both a key signal and a video signal using the [KEY] button in the Setup menu (see page 430). This allows you to select a key signal and video signal using the following methods. • To select a key signal on the cross-point control block in free assign mode or key/AUX bus delegation mode, press the [KEY] button on the cross-point pad, turning it on, and select a key source signal. • To select a video signal on the cross-point control block in free assign mode or key/AUX bus delegation mode, press the [KEY] button on the cross-point pad, turning it off, and select a key source signal. Note When a key source bus delegation button is assigned on the AUX bus control block (AUX bus operation mode), you can perform the operation using the [KEY] button on the cross-point pad. When a cross-point button on the 3rd/4th row is pressed while pressing the [KEY] button, the key signal is selected. When a cross-point button on the 3rd/4th row is pressed without pressing the [KEY] button, the video signal is selected. To select a key source in the menu 1 In the M/E-1 >Key1 >Type menu (1111), press [Key Bus] in the group. 2 Press [Signal Select]. The Signal Select menu (1111.3) appears. 3 In the group, press [Source]. 4 In the group, specify the key source selection mode (Self, Auto Select, or Split). For details, refer to step 5 in "Selecting the key fill and key source" (page 111). 5 If [Split] is selected in step 4, select a key source signal from the list on the right. 6 In the group, select the video signal or key signal from the V/K pair to assign to the key source. Video: V/K pair video signal Key: V/K pair key signal 7 Press [Set Xpt]. To select a key fill in the menu 1 In the M/E-1 >Key1 >Type menu (1111), press [Key Bus] in the group. 2 Press [Signal Select]. The Signal Select menu (1111.3) appears. 3 In the group, press [Fill]. 4 Select the fill signal from the list on the right. 5 Press [Set Xpt]. Carrying out a color mix for key fill When [Matte] is selected for key fill, you can use an independent key transition wipe pattern or dedicated pattern to combine color 1 and color 2. 1 In the M/E-1 >Key1 >Type menu (1111), press [Matte] in the group. 2 Press [Matte Adjust]. The Matte Adjust menu (1111.2) appears. 3 In the group, press [Mix Color]. 4 Set the following parameters. No. Parameter Adjustment 1 Size Pattern size 2 Soft Degree of softness of pattern edge 5 In the group, select the mixing pattern. Key Wipe: Mix using the wipe pattern selected for an independent key transition. Pressing [Pattern Select] opens the M/E-1 >Key1 >Transition/Video Process >Wipe Adjust >Pattern Select menu (1117.2), allowing you to select a pattern. Pressing [Pattern Adjust] opens the M/E-1 >Key1 >Transition/Video Process >Wipe Adjust menu (1117.1), allowing you to adjust the pattern. Key Edge Pattern: Combine using a dedicated color mix wipe pattern for key edge fill. Pressing [Pattern Select] opens the M/E-1 >Key1 >Edge >Matte Adjust >Mix Ptn Select menu (1112.2), allowing you to select a pattern. Pressing [Pattern Adjust] opens the M/E-1 >Key1 >Edge 112