Sony XVS-7000 Users Guide - Page 449
Setting an Input Format Converter, Setting the frame delay, Setting the frame synchronizer
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 449 highlights
When [Adaptive Y] or [Adaptive Y/C] is selected, set the following parameter. No. Parameter Adjustment 2 Motion Select Motion detection sensitivity a) a) 1: Mode with highest proportion converted from frames (still picture priority mode) 2: Mode with higher proportion converted from frames 3: Mode with higher proportion converted from fields 4: Mode with highest proportion converted from fields (motion priority mode) To set the up-converter conversion mode In the group, select the conversion mode. Frame: Conversion in frame units Field: Conversion in field units Adaptive: Detects motion in the signal, and automatically switches mode between conversion using frame units and field units. When [Adaptive] is selected, set the following parameter. No. Parameter Adjustment 2 Motion Select Motion detection sensitivity a) a) 1: Mode with highest proportion converted from frames (still picture priority mode) 2: Mode with higher proportion converted from frames 3: Mode with higher proportion converted from fields 4: Mode with highest proportion converted from fields (motion priority mode) To return the conversion method settings to the defaults Press [Default]. The settings for the selected FC channels are reset to the defaults. Setting the frame delay You can set the input signal delay level for each FC channel. 1 In the Engineering Setup >Switcher >Input >Internal FC menu (7332.5), select the target FC channel to set. 2 Set the following parameter. No. Parameter Adjustment 3 Frame Delay Delay level a) a) The following delay levels can be configured, depending on the switcher signal format. 3840×2160P, 1080P: 1 to 15 frames 3840×2160PsF, 1080PsF, 1080i: 1 to 8 frames 720P: 1 to 15 frames (set value of 1 to 8 frames when the conversion format is 1080i/576i/480i, with an actual delay that is double the set value) Setting the frame synchronizer You can enable/disable the frame synchronizer for each FC channel. When the frame synchronizer is enabled, unsynchronized input signals are synchronized. Note The frame synchronizer cannot be enabled in the following cases. • When the switcher signal format is 3840×2160P or 3840×2160PsF • When the switcher signal format is 1080P and the 720P converter is enabled 1 In the Engineering Setup >Switcher >Input >Internal FC menu (7332.5), select the target FC channel to set. 2 Press [Frame Sync] to enable/disable the frame synchronizer. To enable, press [Frame Sync], turning it on. To disable, press [Frame Sync], turning it off. Setting an Input Format Converter You can set an input format converter, frame delay, and frame synchronizer for primary inputs of the following input connector boards. • XKS-S8111 SDI Input and FC Connector Board • XKS-S8112/XKS-S9112 12G-SDI Input Boards • XKS-C8111/XKS-C9111 100G IP Input Boards • XKS-C9121 100G IP Input and Output Board Note The XKS-C8111/XKS-C9111/XKS-C9121 have the following restrictions. • The input format converter setting is available only when the switcher signal format is 3840×2160P 2SI or 1080P. • On the XKS-C8111, an input format converter can be configured on only the 1st to 4th inputs of each board. • On the XKS-C9111/XKS-C9121, when the switcher signal format is 3840×2160P 2SI, an input format converter can be configured on only the 1st & 2nd and 9th & 10th inputs of each board. • On the XKS-C9111/XKS-C9121, when the switcher signal format is 1080P, an input format converter can be configured on only the 1st to 4th and 9th to 12th inputs of each board. • Frame synchronizer is disabled. 449