Sony XVS-7000 Users Guide - Page 454
Settings Relating to Signal Outputs
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 454 highlights
Settings Relating to Signal Outputs Configures settings for outputs and format converter outputs. The following output connector boards can be installed in the XVS-9000/8000/7000/6000. • XVS-9000 Output connector board Interface XKS-S9167 12G-SDI Output Board SDI XKS-C9121 100G IP Input and Output Board ST2110 XKS-C9121N NMI Input and Output Board NMI • XVS-8000/7000/6000 Output connector board XKS-S8165 SDI Output Connector Board XKS-S8167 12G-SDI Output Board XKS-T8165 IP Output Connector Board XKS-Q8166 QSFP IP Output Connector Board XKS-C8166 100G IP Output Board Interface SDI SDI NMI NMI/ST2110 a) ST2110 a) Interface configured in the Engineering Setup >System >Network Config >Net I/F Protocol menu (7311.3) The maximum number of outputs on the XVS-9000 is 80 (40 for 4K format), or 96 (48 for 4K format) when the multi viewer output connectors are included. For the XVS-8000/7000/6000, the maximum number of outputs on the XVS-8000/7000 is 48 (12 for 4K format), and on the XVS-6000 is 24 (6 for 4K format). The maximum number of format converter outputs is 16 (4 for 4K format). Note 59.94 (2×) format output signals are supported on the XKS-S8165 SDI Output Connector Board only. Network connector board restrictions Only the following interface and signal format outputs are supported, depending on the board. Board Interface XKS-T8165 NMI XKS-Q8166 NMI ST2110 Signal formats • 3840×2160P 2SI (Level A) a) • 1080P (Level A) b) • 1080i • 3840×2160P 2SI (Level A) a) • 1080P (Level A) b) • 1080i • 1080i c) Board Interface XKS-C8166 ST2110 XKS-C9121 ST2110 XKS-C9121N NMI Signal formats • 3840×2160P 2SI (Level A) a) • 1080P (Level A) • 1080i • 720P • 3840×2160P 2SI (Level A) b) • 1080P (Level A) • 1080i • 720P • 3840×2160P 2SI (Level A) b) d) a) Only the first number output in each group of four outputs can be set. b) Only odd-numbered outputs can be set. c) Ancillary data is enabled only on odd-numbered outputs. d) Outputs that are multiples of 8 minus 1 (7, 15, 23, and so on) are not available. For details about 3840×2160P 2SI format output settings, see "4K format output settings" (page 454). 4K format output settings XVS-9000 settings When the switcher signal format is 3840×2160P 2SI or 3840×2160P SQD, only odd-numbered outputs can be set. When the switcher signal format is 3840×2160PsF SQD, only the first number output in each group of four outputs can be set, in the same way as for the XVS-8000/7000/ 6000. Also, when the switcher signal format is 3840×2160P 2SI or 3840×2160P SQD and an output format converter is used, a 3840×2160P 2SI 12G output signal is assigned to a 12G×1 output, hence the setting is available for each oddnumbered output. For 3840×2160P 2SI 3G and 3840×2160P SQD output signals, a group of four outputs is assigned as a group to a 4K signal, and the setting is available for the first number output in each group of four outputs. Notes • When an XKS-C9121N NMI Input and Output Board is installed, outputs that are multiples of 8 minus 1 (7, 15, 23, and so on) are invalid because outputs 7 and 15 on each board cannot be used. • When the switcher signal format is 3840×2160P SQD and you assign multi viewer outputs to output connectors 81 to 96, groups of four outputs are set as a single unit. Only the first number output (81, 85, 89, 93) in each group of four outputs can be set. XVS-8000/7000/6000 settings Four outputs are assigned as a single group to a 4K signal. A single group comprises four outputs in numeric order starting from the first output, and the setting is available for the first number in each group. 454