Sony XVS-7000 Users Guide - Page 444
Setting Through Mode, 4K format input settings, Dedicated inputs, Input signal format conversion
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 444 highlights
Board Interface XKS-C8111 ST2110 XKS-C9111 ST2110 XKS-C9121 XKS-C9111N NMI XKS-C9121N Signal formats • 3840×2160P 2SI (Level A) a) • 1080P (Level A) • 1080i • 720P • 3840×2160P 2SI (Level A) b) • 1080P (Level A) • 1080i • 720P • 3840×2160P 2SI (Level A) b) c) a) Only the first number input in each group of four inputs can be set. b) Only odd-numbered inputs can be set. c) Inputs that are multiples of 8 minus 1 (7, 15, 23, and so on) are not available. For details about 3840×2160P 2SI format input settings, see "4K format input settings" (page 444). 4K format input settings XVS-9000 settings When the switcher signal format is 3840×2160P 2SI or 3840×2160P SQD, only odd-numbered inputs can be set. When the switcher signal format is 3840×2160PsF SQD, only the first number input in each group of four inputs can be set, in the same way as for the XVS-8000/7000/6000. Also, when the switcher signal format is 3840×2160P 2SI or 3840×2160P SQD and an input format converter is used, a 3840×2160P 2SI 12G input signal is assigned to a 12G×1 input, hence the setting is available for each oddnumbered input. For 3840×2160P 2SI 3G and 3840×2160P SQD input signals, a group of four inputs is assigned as a group to a 4K signal, and the setting is available for the first number input in each group of four inputs. Note When an XKS-C9111N NMI Input Board and XKS-C9121N NMI Input and Output Board are installed, inputs that are multiples of 8 minus 1 (7, 15, 23, and so on) are invalid because inputs 7 and 15 on each board cannot be used. XVS-8000/7000/6000 settings Four inputs are assigned as a single group to a 4K signal. A single group comprises four inputs in numeric order starting from the first input, and the setting is available for the first number input in each group. Input number 1, 2, 3, 4 5, 6, 7, 8 9, 10, 11, 12 13, 14, 15, 16 (and so on) Setting number 1 5 9 13 (and so on) Note When an XKS-S8112 12G-SDI Input Board is installed, 3840×2160P 2SI 12G signals are input as a 12G×1 signal, but the input setting is available only for the first number input in each group of four inputs. Dedicated inputs On the XVS-8000, dedicated input connectors 1 to 16 can be used by installing an XKS-S8110 SDI Input Connector Board in slot 1. This allows you to physically connect specific output connectors to dedicated inputs and then select a signal from an output connector as an input. For details about dedicated input settings, see "Setting Dedicated Inputs" (page 445). Notes • Dedicated inputs are not supported on the XVS-9000/ 7000/6000. • Only output connectors on an XKS-S8165 SDI Output Connector Board can be used for dedicated inputs. The following output connectors can be connected. - Format converter output connectors 1 to 16 - Spare connectors 1 to 4 - Multi viewer output connectors 1 to 8 - Output connectors 49 to 52 Input signal format conversion The following format converters can be used. Internal format converter: Configurable when an XKS-8460 Format Converter Board is installed (see page 445). Input format converter: Configurable when an XKS-S8111 SDI Input and FC Connector Board, XKS-S8112/XKS-S9112 12G-SDI Input Board, XKS-C8111/XKS-C9111 100G IP Input Board, or XKS-C9121 100G IP Input and Output Board is installed (see page 449). Note On the XVS-9000, internal format converters are not available. Setting Through Mode Note Through mode cannot be set for inputs whose signal format is converted by an input format converter or inputs with frame delay enabled. 444